hi1) if the AIP-SSM module is installed within the ASA firewall pair then for ASA failover to happen only the AIP-SSM hardware type needs to be same (i.e both should have say AIP-SSM-10) as mentioned in the below document or the software image also n...
Hi.Any one can help me out for installing NAC agent in windows Domain. I have around 1000 Windows clients and i have to install on each and every one from domain controllerI Guess the MSI Installer is the best option.Any one?
i get following message when trying asdm(https://asa-ip) with ASA 5520 , 8.0 rel 4.asdm image disk0:/asdm-506.bin The requested URL /admin/public/index.html was not found on this serverasa ip is 192.168.200.25. related configuration on asa is,http s...
Hey all,I am in dire need of some help. I am currently trying to open my NAT for use with Xbox live. I have searched the forums and found great information but I cannot seem to get it to work for me. If I do not use any port forwarding rules at al...
I've been researching what my options are for capturing logs remotely. Any comments are appreciated.1. Syslog to a syslog server in cleartext over the internet is out for obvious security reasons.2. Site to Site vpn to a syslog server is possible, bu...
Hello,I am having problems with a FWSM with multiple contexts implementation.One of the contexts has a inside interface that must have a EXPLICIT deny ip any any.The problem is:When I put the ACE with the explicit deny at the end of the ACL all the t...
Hi , I have a quick question regarding the ASA-5585 with 2 10Gig port IPS module. When the IPS module runs a separate application from ASA and the traffic between the ASA/IPS is flowing in the back plane, what is the use of having two 10 Gig ports...
Need to configure HSRP in routers, But in ASA i have only one gateway ROUTER 1-->ISP1LAN --->ASA--->L3----> ROUTER 2--->ISP2in the above setup explain,In ASA, 2 interface used ...
Hi,i have a Cisco ASA 5550 with firmware version 8.2.I have read the documentation about the static routing tracking feature.Is this feature working if i set two static routes with different metrics to the same destination subnet, but one route is ap...
Hello All, I am New to the ASA/IPS world,and i have a few questions.We are buying two ASA5520's with IPS Modules(aip-ssm-10) for a new location, I plan on running them in active/standby. These will be my first set of ASA5520's.My Network design for t...
HelloI tried to seach, but I did not find correct solution to my problem.I haveCisco ASA SEC PLUS running in Main office AOutside interface- default ISP InternetInside interface - default local lan. 192.168.1.0/24DMZ interface - other external networ...
Hello,I have a Cisco Pix 515r with a VPN set up.I have 4 remote users from the same location trying to connect to my VPN. It appears that only one can connect at a time. I believe this is an issue on their side not mine. But since I'm "somewhat" f...
Were trying to use our polycom VC through our ASA 5510 but everytime someone calls in we see a Deny Outside_in destination port 1720 tcp in the syslog.It doesnt make sense as we have all the following ports open on the outside interface (H323 coloum)...
I would like to create exceptions within particular signatures to ignore IP addresses. How do I perform this task?
Hello,I have just setup a new ASA 5520 with 8.3 OS. I have it setup very basic with 3 interfaces; outside, inside, and management. I have it setup so any users on the inside can get to the internet on the "outside" with Dynamic NAT. However I a...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 12-05-2025 12:44 AM | ||
| 11-13-2025 12:52 PM | ||
| 11-03-2025 09:48 AM | ||
| 10-30-2025 12:44 PM | ||
| 10-23-2025 07:14 AM |
| User | Count |
|---|---|
| 5 | |
| 4 | |
| 3 | |
| 2 | |
| 2 |
