Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

Hi,would anybody be able to help me to configure asa 5505 to achieve these requirements please?- 3x interface outside, inside, dmz- some traffic needs to go from outside to dmz web server and then be forwarded to inside ip address or group ip address...

patrifick by • Level 2
  • 3044 Views
  • 6 replies
  • 0 Helpful votes

We have been assigned a new range of ips 213.x.x.x/28 from our ISP. They are being routed via our existing gateway 92.x.x.146.The problem:We can't get any traffic to this pix on the new range 213.x.x.x/28. - If we try to ping 213.x.x.61 we get Time t...

dsc_tech_1 by • Community Member
  • 4420 Views
  • 9 replies
  • 0 Helpful votes

HelloI have an ASA with to contexts which share two interfaces (see attached graphic). Both contexts run on the same 5540I want to ssh Context B firewall from the Intranet, but it doesn't work.IP Routers are ok.I have configured access-lists on Conte...

seba by • Level 2
  • 2635 Views
  • 1 replies
  • 0 Helpful votes

Folks,trying to set up security context for one of our remote clients. they have an ASA 5540 and want to use it for seperating their own & their subsidaries traffic flow. Would each of these contexts have their own seperate interface details? Will th...

suthomas1 by • Level 7
  • 4726 Views
  • 7 replies
  • 0 Helpful votes

Hello, I have a DSL line with 3MB symmetrical upload and download. How can I guarantee 600 Kbps for a video stream that we emit? At the same time, I want this 600 Kbps available to the other traffic, when no broadcast video. Is it possible?What is th...

jmprats by • Level 6
  • 1541 Views
  • 2 replies
  • 0 Helpful votes

Resolved! Syslogging

Has anyone experienced problems changing the logging severity level of a Syslog ID to either raise or lower its level within the ASDM?  I want to log certain activities that are currently set as notification and informational but don't want to log ev...

jamesfick by • Community Member
  • 1236 Views
  • 2 replies
  • 0 Helpful votes

Hello,I upgraded from 4.5.1 to 4.7.1. I am having trouble with the communication between the CAS and the CAMHere is an outline of the issue1.       After Authentication, DHCP, ACS ok, WALL !!!2.       Nac Online Users = 03.       Ping the CAM HA serv...

kysersosai by • Community Member
  • 2906 Views
  • 1 replies
  • 0 Helpful votes

I am trying to setup a second vpngroup on a pix 6.2 (I knowit is old but can't upgrade it yet) and am having a problem. I can connect to the new vpngroup and it works when there is not split tunnel configured butwhen I add the split tunnel command it...

nickehunt by • Community Member
  • 1122 Views
  • 1 replies
  • 0 Helpful votes

Hi allWe use 2 FWSM version 3.2 (4) in active-failover, transparent, multicontext mode.I have now a problem with backuptraffic (TCP) between an application server and a backup server through firewallthat traffic hangs after 1,5 hours. In the sniffert...

marcopolo by • Visitor
  • 2816 Views
  • 3 replies
  • 0 Helpful votes

I have a Cisco ASA 5510 with the CSC-SSM module installed.  Is there a way to configure the CSC-SSM to block web sites but also allow specific users access to these sites?

ferraromj by • Community Member
  • 3091 Views
  • 8 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card