Couple questions. About to implement this scenario with two ASA5520s. I plan to have these two connected to two 4506s running as core switches. My question is do the ASAs need a dedicated link to each other for their communication or can they communi...
Hello Everyone,We are replacing all of our PIX firewalls in our main data center with ASA 5550s. We have 7 pairs of the 5550s, what would be the best design scenario to setup the LAN/Stateful failover connection? The documentation states, you can hav...
When I trie to add an IPS device (ASA-SSM-10 version 7.0(1)E3) into my devicelist within IME 7.0.1 i'm getting the following error:Error response from IME server: - IOException: Read timed out. IME IME serveris not ressponding. Please check if it is ...
I know how to enter static ip info to the outside interface. You then enter in a default route for the gateway statically. But, where do you enter in the static dns servers provided by the isp? does that fall under dns server-group defaultdns group w...
Hi everybody,I have trouble with FTP connections using a ASA5510.I have 3 LANs connected to the FW:LAN1 (inside): 172.16.1.0/24LAN2 (outside) 10.52.64.0/24LAN (DMZ) 172.16.0.8/29My FTP server (IIS FTP Server)is on the DMZ with IP address 172.16.0.10....
Is it possible to rate limit, or police, the bandwidth for some users while not for other users? Can this be done based on the type of traffic? Source/destination?TIA
Hi All, The below interface on the PIX 535 is having a lot of CRC and input errors. what can be the reason ? and how to solve it? let me know if any further information is required.Interface Ethernet1 "3PGW", is up, line protocol is up Hardware is i8...
Hi,I need steps to allow traffic from inside to outside for IPSEC / PPTP / SKYPE on ASA 5520 and block http and 8080
This is more or less a question regarding how the ASA allows traffic to traverse itself.If I understand the ASA properly; all unicast traffic is permitted from a higher security interface to a lower security interface and only inspected traffic is al...
HiI have ASA 5540 whose Gig2 interface is subinterfaced into 3-vlans 40,50,60.Do I need to trunk the port(cable is coming from ASA Gig2 interface) on the switch and create VLANS 40,50 and 60 on the switch in order to get the hosts in these vlans work...
Hello,I've got the following setup:WinXP laptop (host) with CISCO VPN client installedMS Virtual PC 2007 Guest VM (WinXP).When working from home I want to get the following to work:Start laptop (with host WinXP).Start Cisco VPN Client on host and aut...
Hi,I came across a problem after configuring QoS on a ASA5505 v8.2(1) for one of our customers (planning to use IP Phones over VPN). Although I configured via ASDM, here is the relevant CLI config:priority-queue outsideclass-map DM_INLINE_Child-Class...
Hi,I have a Cisco877 router that is used for internet access, I was wondering if its possible to set up a default URL page that is loaded as soon as someone try's to access the internet via this router - we want to add an acceptable internet usage po...
The NAT's I have set up on the main outside interface work fine, but if I try to add a nat another IP on the external network (it's a /29) network, it doesn't work. I have only two VLANS inside and outside.When I simulate traffic on the simulator it ...
Hi,We are in process of configuring FWSM failover. On cisco's website example is given with all the necessary commands.I still have one doubt Following is the configuration:on FWSMnameif 4000 failover 50ip add failover 10.40.40.1 / 24fail ip address ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 09-22-2026 04:13 PM | ||
| 08-25-2026 06:22 PM | ||
| 08-24-2026 12:26 AM | ||
| 08-20-2026 05:54 AM | ||
| 08-19-2026 07:59 AM |
| User | Count |
|---|---|
| 3 | |
| 1 | |
| 1 | |
| 1 | |
| 1 |
