Buy or Renew
Buy or Renew

Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

“Join

 
Labels

Forum Posts

Start a conversation

Resolved! Cisco ACS & remote agent

Hi,Is it mandatory that remote agent for ACS be installed on main domain server, would it work if it were to be installed on a virtual server which is member of the main domainserver?This is to be used for authentication with a vpn opertion.What impa...

suthomas1 by • Level 6
  • 494 Views
  • 1 replies
  • 0 Helpful votes

ASA5520 - IP Using Old Translation

hey all, we originally had a one-to-one static translation from private to public IP. the translation has been removed and the private is supposed to be using the global nat pool. but, for some reason, it is still using the public ip originally mappe...

Robert Ho by • Level 1
  • 686 Views
  • 4 replies
  • 0 Helpful votes

UDP and NAT problem

DMZ = 172.16.1.0/24Screened Subnet (behind ASA) = 172.16.3.0/24I have numerous static NAT entries for HTTPS traffic to the 3.0 network, advertised on the outside as a 1.0 address.The 1.0 network is a directly connected network between my border and t...

Resolved! 2 public subnets on an ASA 5510

I've seen some posts where the following scenario is working and most other posts that state that the following scenario cannot be accomplished on an ASA 5510.We have an ISP that is pushing out two separate public IP ranges, and we are to implement a...

throttling a runaway host

We've got a security server running Retina that recently ran away and opened up tens of thousands of connections through our Pix 515E to devices it's supposed to scan. This caused memory on the PIX to run low, caused dropped connections on other ses...

Very weird issue with our FWSM

Hi allWe have a redundant Cat6500-E with Sup720-3B and FWSM setup.Software releases:Sup: 12.2(33)SHX2FWSM: 3.2(6)The issue, if I add several new VLANs to the Catalyst and then give them to the FWSM with the command:firewall vlan-group 1 14-18,20,21,...

patoberli by • VIP Alumni
  • 733 Views
  • 4 replies
  • 0 Helpful votes

ASA VPN to IOS

All,I have an ASA 5505 that I'm trying to get a tunnel up with a 2800 series router. The tunnels get established, but the ASA side is encapsulating and not decapsulating traffic and I'm not able to pass traffic.I have the following:WinXP host (10.125...

FW in VSS Environment

Working in a VSS environment, one firewall in each catalyst, configured with two context and Active / Passive scenario. One VLAN exist between two context, but no communication between context over the VLAN. ARP is showing same mac-address on two dif...

Query on Time Based Access-lists

Hello Experts,I have been using the time based ACLs for quite a while now. But I never able to figure out, to how many time-ranges we can create on a ASA 5510 and ASA 5520. Is there any limitation to that, to how many time-ranges we can define?Thanks...

arabindas by • Level 1
  • 474 Views
  • 1 replies
  • 0 Helpful votes

Resolved! same security level rules

Hi,I came across some interface on our firewall with same security level & also ACE corresponding to each of these interfaces.I also found that "same security level command" has been enabled on the firewall. Question:If 2 interfaces with same level s...

suthomas1 by • Level 6
  • 568 Views
  • 3 replies
  • 0 Helpful votes
Load more
Review Cisco Networking for a $25 gift card