Network Security

Hi there..There are 2 interfaces configured on ASA, where one is connected to 10.x.x.x and the other connected to 192.x.x.x ..the problem is there seems to be no communication between these two..any suggestions.FYI: they hav the same security level a...

Hi you all.How can I see (know) the license installed on a PIX 525?or how do I backup a license?thanks

Hi,Internet slow response------------------------Scenario:-FWSM-----DMZ------Websense is connected and outside segment.Inside users ar accessing the internet first it will go to the websence and filter, it will redirect to Outside segment.Conf:sh url...

Hi,yesterday, after succesfull upgrade FWSM from c6svc-fwm-k9.2-3-4.bin to c6svc-fwm-k9.3-1-3.bin the module did not start. #show module 1Mod Ports Card Type Model Serial No.--- ----- ------------------------...

Hi All,I need to block certain web pages with my ASA but I don't have a Websense or N2H2 server. I've heard that you can do this with the ASA itself using Regex. My question is, is this really a good/easy way to do it? Does it really works fine?Thank...

Hey Everyone,I just got a new 5510 and need to get a polycom head unit to NAT through and it doesn't want to seem to play nice. (At least that is what I think it is) I have set up a static nat for the unit itself and set up an outbound and an inbound...

There are a few computers in the building that when they start i have to do a repair in the connection. If i put those same computers in the admin Vlan(doesn't goes through NAC) i dont need to do the repair. I think something is blocking in the una...

How do I get a different SSL certificate, so this is not an issue: http://www.cisco.com/warp/public/707/cisco-sa-20050824-idsmc.shtmlCan I simply purchase a certificate from VeriSign? If yes how do you install them?Thanks,

I am trying to setup my PIX 501e and i am having trouble. i'm trying to set it up as simple as possible. authentication to be done local on the PIX, just one user is fine. no AAA server. once in, i want to permit all ports for all traffic. i think i ...

Hi all, when configuring failover on the cisco asa, my book says you configure the failover on the interface, like this failover lan interface MFAILOVER gigabit interace 0/3what does the MYFAILOVER mean? is this just the name of the interface that yo...

Hello I need help regarding my ASA configuration. As it turns out I need to allow my inside vlan to communicate with my insidevoice vlan. I am not sure what could be missing in my configuration below:ASA Version 7.0(8)!hostname ASA!interface Ethernet...

Does the license limit of 10 inside hosts apply only to hosts to go out to the internet or will it apply also to hosts that go through a lan to lan tunnel I created? I will have about 20-25 PCs on a lan behind a ASA that's gonna be linked to our main...

The CSC-SSM Administrator Guide states that once the failover peer device is detected, one should see 'synchronize with peer' on the primary device window. But in my case, both primary and secondary are showing the 'sychronize TO peer' button. Is som...

HiI've got a an active/standby pair of ASA's and I've been given a point-to-point circuit to connect into it. My problem is that I only have one ip address but when creating the interface I don't know what to do about the standby configuration. Curr...

Hii have a 6500 switch with FWSM .Its outside interface ip address is 64.x.x.219.all the users behind the firewall are natted on the firewall with 64.x.x.220.nat(inside) 1 0.0.0.0 0.0.0.0global (outside) 1 64.x.x.220 netmask *****.we have some server...