Network Security

Hi,I have configured FTP server in my local server and nated the ip in the ASA and also given inbound access.Now the problem is i am able to access FTP through command from outside(NATed IP) but it's not accessable through web. ftp://x.x.x.xFrom insi...

New ASA, was made "config factory-default"Then I set to Ethernet 0/0 192.168.164.56/22. But when I tried to ping it "ping 192.168.164.56", I've got "No route to host 192.168.164.56". What's the problem?------My running-config:ciscoasa# show running-c...

Hi,How do you configure the primary unit to be the always the active FWSM when both the primary and secondary units are up (after a failover to the secondary)? According to the Cisco website, the command "Failover preempt" on the primary unit should...

Hello,I have configured admin context on my FWSM as transparent FW with vlan 911 being the outside and vlan 11 being the inside interface...I have created both inside and outside ACLs to be permit icmp any any and ip any any but somehow hosts on the ...

Total noob...My laptop can establish a vpn connection to a site when I am at home. Bring it to work, it can't establish thru the 5505. Can you tell me what I need to enable so I can VPN through it? I have searched and tried different things to no ...

Does the SAS 5505 support this:In order to 'upgrade' the ISP's upload speed (800k) is it feasable to just install a second modem (with second line and fixed IP of course)and load balance? or maybe connect VPN from 2 branch office on one and another o...

I have a Cisco ASA 5520 with a DMZ and an inside interface. The security policy is setup to permit IP ANY from host on DMZ to host on inside. The host on the DMZ is initiating communication on UDP port 2114 which is a challenge response authenticat...

How do I migrate configurations from ASA5520 to PIX515E.

How many network objects can be in a Network Object Group, current have 1023 and may need to add 1123 more, thank you.

I am currently running Cisco IPS 4260, CS-MARS v4.2, and CSM 3.1.0.I want to create a custom signature in all my IPS 4260's which monitor activity from and to several external IP addresses and have it send an alert to my MARS device. How can I do th...

HI.I need configure a vpn site to site between 2 cisco routers.My lan is:Fastehernet0 (wan) : 213.27.220.214vlan1: 10.0.0.0/24 router:10.0.0.251etc...In wizard(img1.jpg) I don't know where have every type:for example:1. Select the interface for t...

Hi,I am trying to generate trap from IPS 4215 6.0(4a)E1 to HP Openview.I configured snmp section and required action (request snmp trap) using IDM.I have alerts in event viewer but the only thing I get in trapd.log is: 1207730797 1 Wed Apr 09 10:46:3...

Hi All, I have 2 3750G series switches on the trunk link. some machines are part of vlan1 on the switch 1 and some machines are the part of the same vlan1 on the other switch2. I need to limit the bandwidth between the switches for the vlan1. picture...

I need help regarding the following issue..An asa is connected to a router which is connected to the internet. A vpn must be established b/w ASA and a router that is over internet . The ASA is not directly connected to the internet. It is connected t...

I'm a new and novice user of CisoworksI have been navigating through the package for two days now and have discoved how powerful the tools are Can some direct me to the area to udpate a Sig of an IPS I believe that it may be in the Software Mangement...