Hello,We have Cisco FMC\FTD (Version is 7.0.1) integrated with Azure SAML for Anyconnect MFA, also done integration with Active Directory for other purposes. Authentication works, I can connect to the Anyconnect. But now I need to also provide Author...
Hello, I have a layer 3 switch (Cisco Catalyst 3650) with multiple vlans configured on it, and connect to this switch to inside interface of ASA.My goal is make all vlans can go through firewall and asa route beetween VLAN-s not Layer3 switch.Inside ...
Hi,I have an issue with Cisco Firepower Threat Defense for Azure. It often alert severity critical for CPU Usage.Randomly check shows CPU around 50%. Could you advise where I should check further?Below is detail: FP-East# sh cpu detailBreak down of p...
Hi,Could you please help on disabling telnet feature on CISCO ASA5505 router which is running on ASA software/firmware 8.2. I mean I would like to disable telnet completely on the router. Thanks...
Cisco documents says that FP2100 series support hardware bypass, but it seem they're only some modules of FP2130/2140 supports hardware bypass, FP2110 doesn't support hardware bypass. Is that true?
Hi Cisco community.I am faced with a boot issue after an improperly implemented upgrade to Cisco Adaptive Security Appliance Software Version 9.18(1).The previous version was Cisco Adaptive Security Appliance Software Version 9.17(1)Now I see these m...
Hello,I recently had to re-format, add a new activation-key, and add the asdm504.bin and asa704-k8.bin to my ASA 5520 (I accidentaly erased the memory on the machine). Now currently everytime I use the "reload" command it just loads straight into Rom...
I setup a pair of 2110s (6.5.0.4) in HA that are managed by an FMC w/ a port-channel facing the LAN and a single outside interface for now. I set the port-channel and the outside interface to use a virtual mac address for the active and standby unit...
Dear ,we noticed that cisco firepower FTD 2130 is sending DNS requests to the open DNS 208.67.222.222 which is not required and we didn't configured.we need to disable this featrue , please advice
Hello, We are currently using flexconfig for PBR but after upgrading to 7.2, PBR can now be configured through FMC's Policy Based Routing page. Anyone tried to configure PBR this way? Should we deploy the configuration once after we remove the flexc...
Hello,I'm trying to upgrade/re-install the IOS for Firepower 2110. I have downloaded the asa image (cisco-ftd-fp2k.6.4.0-102.SPA) when I try to upload it to the FTD, I will get a failed message when I check the show download-task details. Model : C...
Hey Guys,i tried basically everything in the internet.My ::> show run Any more parts interesting for you? What am I missing.> -----curl https//:{host}:443 -u "name:pw" ------------ is not working either! Postman neither! Browser neither... Chrome is ...
We have a Cisco ASA 5525. There are many references to a server "dc" in the ASDM. The ASA is using "dc" as a DNS server, it's using "dc" as a radius server. And all of these things are working properly and I'm able to ping "dc" from the ASA. However ...
Over the past month, we've found two vendors who are using VPN connections from their systems on our network that we were unaware of. I've been searching for a way to block unauthorized VPN connections - one is running on port 443/tdp and the other o...
Hi, so my 1 of my HA FMC MonetDB is Crashing right now.The solution i think about is by reimaging the FMC. I want to know if i reimage the FMC does it restore the MonetDB or it just gonna be the same MonetDB as before?Also, i have 2 FMC in HA mode, b...
