I?m in the process of installing an ASA 5505 to a T1 circuit for Internet access. I will be setting up the ASA with 3 Vlans. The inside Vlans will be Home and Business. The outside will be for Internet access.I would like to make sure that I have acc...
Can anyone else pull a report from CSA-MC 5.2 with a separate MC and DBI get the following error.Error: Operation failed. See csamclog.txt for details.I look it up on the server and is says""[2007-07-09 15:42:59.359] [PID=9900] [webadmin]: Error :...
Hello:I wish to build 2 GRE/IPsec tunnels from a 2811 (IOS 12.4(3g)) running to 2 differing PIXes which are located in the same place (1 is a 505 running 6.3(4) and the other a 515e running 7.2(1)).One tunnel will be used as primary and run over a Se...
Hi We have PIX version 7.0. Netscaler in the dmz, and virtual server ip is the 192.168.8.98 (dmz network 192.168.8.0). inside web server is 192.168.0.250 setup with virtual server. If I setup a static (dmz,outside) 12.x.x.x 192.168.8.98 netmask 255....
Hi,I have a big network comprising of 10.0.0.0my inside interface ip is 10.100.1.1 /24my management interface ip is 10.150.1.1 /24The default inside route in my ASA is route INSIDE 10.0.0.0 255.0.0.0 10.100.1.1From my user network - 10.200.1.X, i try...
I am going to purchase a Cisco ASA5510. What what is the recommeded training course for configuring the ASA for firewall? It looked like the SNPA focused quite a bit on VPN
Hello,I'm trying to redirect outside port connections destined for a specific "sftp" server by accepting port 22 connections destined for the sftp server and redirecting to port 2222 on the sftp server through the PIX.static (inside,outside) tcp inte...
Is there a particular software revision I will need on my Cisco 3620's and 3640's in order to get them to function with the IDS 4210? Or does the IDS do all that for me? I haven't tarted the IDS up yet so I am new to this.
I have some servers on our inside network that have a secondary NIC for replication and failover purposes.This secondary NIC on the inside servers is in it's own seperate VLAN (10.10.10.x).We need to add this set up to a couple of DMZ servers.I want ...
Hello,A few of my customers are utilizing ASA-SSM-10 module running under ASA5510/20 hardware. The FW?s is part of the Failover configuration.The module is running in "promiscuous fail-open" mode and the class-map for the IPS is applied as global_po...
Hi - I have a number of IDSM-2 cards I've recently upgraded from 4.x code to 5.1.1 IPS code. Since the upgrade, I am having frequent issues with the sensing interfaces (gigabitEthernet0/7 and 0/8) going errorDisabled. Of course I am not able to do ...
Hi Pix 6.3, enable snmp-server host to a windows 2003 server running MRTG. When MRTG try to get traffic from PIX inside interface, nothing show up. No errors in pix and windows, ping is fine. Could help to list some documents about PIX 6.3 snmp setu...
I have PIX 515E Firewall when I statrt it the following message appear in Hyper Terminal.CISCO SYSTEMS PIX FIREWALLEmbedded BIOS Version 4.3.207 01/02/02 16:12:22.73Compiled by morlee64 MB RAMPCI Device Table.Bus Dev Func VendID DevID Class ...
