Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

Dear all,We have a PIX 525 with failover bundle. I would like to know how to upgrade my OS from ver 6.3 to 7.0 in both the Active and Standby firewall.I would also like to know the bugs/problems that we might face after upgradation and whether it sup...

netadmin by • Community Member
  • 661 Views
  • 2 replies
  • 0 Helpful votes

I have a PIX 515E with boot problem. These are the lines I received from the console:CISCO SYSTEMS PIX FIREWALLEmbedded BIOS Version 4.3.207 01/02/02 16:12:22.73Compiled by morlee32 MB RAMPCI Device Table.Bus Dev Func VendID DevID Class Irq 00 00 00 ...

mbonilla by • Community Member
  • 629 Views
  • 1 replies
  • 0 Helpful votes

Is it a way to allow broadcast on a defined port through a PIX. For example host A broadcasts on udp port 234 and is connected to interface A on the PIX. Host B is connected to interface B on the same PIX and should see this broadcast.

thestholm by • Community Member
  • 532 Views
  • 1 replies
  • 0 Helpful votes

Hello, I've been looking through the forums and have been seeing different answers to this:Say I have two PIX 515e's running V7 in failover - I've got 6 interfaces: outside, dmz1, dmz2, dmz3, failover and inside.Can I run multiple VLANs in dmz2 for e...

monkeyboy by • Level 2
  • 1691 Views
  • 3 replies
  • 0 Helpful votes

When i boot my PIX 501, it get stuck over hereany clueRegards manishCISCO SYSTEMS PIX FIREWALLEmbedded BIOS Version 4.3.207 01/02/02 16:12:22.73Compiled by morlee32 MB RAMPCI Device Table.Bus Dev Func VendID DevID Class Irq 00 00 00 8086 7192 Host Br...

I guess the big red check by my other thread is keeping folks from replying, so I'll try another one. I was having problems with the Cisco VPN Client last week after installing/uninstalling ZoneAlarm. Over the weekend after sitting down and cleaning ...

I have a Cisco PIX 515E running version 6.3(4). It has three ethernet interfaces. Is it possible to have two WAN connections coming in through it with one LAN connection? For example.eth0 - public IP address (ISP #1)eth1 - public IP address (ISP #2)e...

phusion2k by • Community Member
  • 576 Views
  • 1 replies
  • 0 Helpful votes

Dear all, i have the following problem: On the DMZ of the PIX we have two servers:-primary with address X-secondary with address Y-network load balancing address of two servers ZWe need to nat mail messages to and from IP M according to the following...

tamerfathy by • Community Member
  • 510 Views
  • 1 replies
  • 0 Helpful votes

Hi,Pls find the attached diagram.the requirement is:1. inside servers should ping pix inside,dmz,outside interface.2.the server in pix dmz should be able to ping pix dmz,inside,outside interface and all servers inside.3. from ISA i should be able to ...

If a new modular policy is defined and applied to an interface, does the default global policy (policy-map asa_global_fw_policy) get applied too, or does the contents of the new interface policy need to include the actions of the global policy. I am ...

Review Cisco Networking for a $25 gift card