Network Security

I am configuring a pix 515e with 6 interfaces. Right now 3 are enabled, 0,1,4. I also have a 1760 router and a catalyst 1950 switch. the switch is configured in 4 vlans with vlan 1 ip 10.1.0.3 the router connection is on vlan 1 port 0/2. The pix is a...

Hi all, I've configured lac shaping for upload on my 2811 (ios xxx124-7.bin) as per:http://www.cisco.com/en/US/partner/products/ps6350/products_configuration_guide_chapter09186a0080455ade.htmlHowever it's not working. I suspect IOS fault, just wanted...

Hello I have a pix Cisco 515 with three interfaces. IP addresses are as follows: Inside : 10.10.10.1DMZ : 10.10.11.1Outside : 10.10.12.1The exchange server's address in local area network is: 10.10.10.200The SMTP mail relay server’s address in DMZ ...

All, I have set up a site to site VPN with a remote office, the remote office has a 501 and my site has a 515. The tunnel works fine, however my users in the remote office complain about the speed...we have a leased line of 2mb the remote site is in ...

I am currently in the process of configuring MARS to monitor two Cisco 4215 IPS sensors. I have rebuilt both of the sensors with the latest software (5.1d) and signatures and they are loggin events as expected.My question is, where is it best to fil...

Hello- I hv PIX 515E with 16MB flash,64MB RAM & VAC for which I am building failover.The failover bundle has come in with PIX515E-FO with 16MB flash,128MB RAM & VAC+.I understand both primary & secondary has to hv identical config for the failover to...

We have a 6509 running 12.2.18SXF with an IDSM-2 (5.0(6)). We are using VACLs to capture traffic from several VLANs onto the IDSM. Today, we added another VLAN to the IDSM by creating a VACL for that VLAN with the "action forward capture" statement. ...

My PIX-515 is working properly and has these files:Directory of flash:/6 -rw- 1726 13:19:48 Apr 07 2006 downgrade.cfg9 -rw- 1925176 13:20:16 Apr 07 2006 image_old.bin12 -rw- 5437440 14:03:23 Apr 07 2006 pix704.bin13...

I'm experiencing an issue updating my IDSM-2's. I'm currently at 5.1(1p1)S223.0V1.0, I tried applying the latest signatures (S224), but failed and got the following message: "Exception during sensor reimaging: Timed out while waiting for sensor to c...

Can a 5510 with active/passive failover do statefull failover for VPN tunnels? By that I mean do the SAs get passed to the standby unit so the tunnel would not go down when it fails over?

After I log on the PIX,I can obtain a IP address from the local pool kbvpn,but I can't go to the internet.The attachment is the configuration of the PIX.

I have 2 sites that have the failover bundle running 6.3(5). I was not able to log into the first site tonight but was finally able to after I logged into a server on the inside and then ssh'd back to the secondary. I had to then switch the active ...

We have some 871's which will not pass telnet through the router, to the devices on the other side. Some will, other won't. Config's are identical, except for where the DHCP pool (dns-server) is getting the information. The one in serious trouble ...

hello, from the inside interface I get many errors on my syslog server.. is there any way to see what these errors are?