Network Security

Hi,how to enable telnet to pix outside interface.I try to connect with telnet to a router in outside lan and then i would connect with telnet form router to pix.Router have ip address 10.10.10.1 and Pix device have ip address 10.10.10.2.I have tried ...

Dear all,We have a PIX 525 with failover bundle. I would like to know how to upgrade my OS from ver 6.3 to 7.0 in both the Active and Standby firewall.I would also like to know the bugs/problems that we might face after upgradation and whether it su...

I have a PIX 515E with boot problem. These are the lines I received from the console:CISCO SYSTEMS PIX FIREWALLEmbedded BIOS Version 4.3.207 01/02/02 16:12:22.73Compiled by morlee32 MB RAMPCI Device Table.Bus Dev Func VendID DevID Class ...

Hi,I think this is probably the best place to ask! I'm not really interested in the certification...Does anyone know if one of the Cisco courses gives good training on PIX v7.0 and for the Firewall Services Module, also if the training covers topics...

Is it a way to allow broadcast on a defined port through a PIX. For example host A broadcasts on udp port 234 and is connected to interface A on the PIX. Host B is connected to interface B on the same PIX and should see this broadcast.

Hi, I´m in urgent need for help. I have bought an Pix 515E for the company.First i connected the firewall and all outbound traffic was ok, but naturally no inbound traffic as mail got through.So i tried to set up some rules (2), and they didn´t work ...

Hello, I've been looking through the forums and have been seeing different answers to this:Say I have two PIX 515e's running V7 in failover - I've got 6 interfaces: outside, dmz1, dmz2, dmz3, failover and inside.Can I run multiple VLANs in dmz2 for e...

Hi all,I have read that PIX version 7 and up allows "hairpinning" encrypted traffic. That's beautiful, but did someone find out how to route regular IP traffic through the same interface (same security level) on a PIX running version 7up? Alernativel...

HI,i am currenty planning an upgrade for two pix and FWSM in active stanby mode from version 7.0(1) to 7.0(2) and 2.3(2) to 2.3(3), but i haven't find any info about this type of migration. Since this is a not a major upgrade, can anyone tell me w...

When i boot my PIX 501, it get stuck over hereany clueRegards manishCISCO SYSTEMS PIX FIREWALLEmbedded BIOS Version 4.3.207 01/02/02 16:12:22.73Compiled by morlee32 MB RAMPCI Device Table.Bus Dev Func VendID DevID Class Irq 00 00 00 ...

I guess the big red check by my other thread is keeping folks from replying, so I'll try another one. :)I was having problems with the Cisco VPN Client last week after installing/uninstalling ZoneAlarm. Over the weekend after sitting down and clean...

I have a Cisco PIX 515E running version 6.3(4). It has three ethernet interfaces. Is it possible to have two WAN connections coming in through it with one LAN connection? For example.eth0 - public IP address (ISP #1)eth1 - public IP address (ISP #2)e...

Dear all, i have the following problem: On the DMZ of the PIX we have two servers:-primary with address X-secondary with address Y-network load balancing address of two servers ZWe need to nat mail messages to and from IP M according to the following...

Hi,Pls find the attached diagram.the requirement is:1. inside servers should ping pix inside,dmz,outside interface.2.the server in pix dmz should be able to ping pix dmz,inside,outside interface and all servers inside.3. from ISA i should be able to...

If a new modular policy is defined and applied to an interface, does the default global policy (policy-map asa_global_fw_policy) get applied too, or does the contents of the new interface policy need to include the actions of the global policy. I am ...