Network Security

Engage with peers and experts on network security topics such as FTD, FMC, FDM, CDO and ASA.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Cisco CyberSecurity

Labels

Forum Posts

Hi guys, mind looking at my config and helping me figure out why any box in the DMZ can not be accessed from the outside.. They also have no access to the net? I looked at couple example configurations and i must be missing something every single tim...

bob by Beginner
  • 603 Views
  • 9 replies
  • 0 Helpful votes

i understand that ospf is supported on pix 6.3..But how it is implemented..i couldnt see any sample configurations or even documentaion guidelines on how to implement it...anyone could suggest any link pls will be greatly appreciated.

rpalacio by Beginner
  • 195 Views
  • 1 replies
  • 0 Helpful votes

I have a PIX 506 that was connected to a ISDN with a static IP. Now we went to ADSL and we don't have a static IP. Is it possible for me to set the outside adapter to DCHP and have it work correctly? From the limited reading I don't think it is posss...

ddevecka by Beginner
  • 369 Views
  • 3 replies
  • 0 Helpful votes

I'm trying to connect a PIX FW and a VPN 3015 with the use of certificates.I followed the instructions found in TAC, but at a given moment there's a command that configures your CA server to get the certificates, and it's here that it goes wrong.--> ...

SDWorx_2 by Beginner
  • 465 Views
  • 4 replies
  • 0 Helpful votes

Hello,I want to configure the pix to redirect the trafic in one external ip to different internal ips depending of the port requested. I have tested it using static command and has worked with some test but when I change the ports to the real ports t...

franspain by Beginner
  • 203 Views
  • 2 replies
  • 0 Helpful votes

I have a VPN Tunnel from PIX to NMS-DMZ.now i want to enable logging on the PIX (on the same as the Tunnel starts) to the NMS, but it seems that the packets are not entering the tunnel. how can i route the Packets into the tunnel?thanks Phil

4priedo by Beginner
  • 921 Views
  • 2 replies
  • 0 Helpful votes

I have a server with real IP 90.0.0.50 has Natted to 172.20.1.1 as follows;static (inside,outside) 172.20.1.1 90.0.0.50 netmask 255.255.255.255 0 0 If I want to allow 172.20.7.0 network to access server network , what is the correct IP to be defined ...

Hi All..Am trying to setup a remote site using a Pix506e on the remote end and a 3005 Concentrator at the headend. I am getting an error on the pix that says "VPN Peer: ISAKMP: No remote peer info for 12.109.169.12/500 - peer:0" That IP address is ...

rserao by Beginner
  • 872 Views
  • 2 replies
  • 0 Helpful votes

Hello .. Is there a way to do simple URL filtering on the 501 without the use of websense or similar external products? I have searched through the postings in this forum but have been unable to find anything similar?Basically, using an acl or equiva...

phalin by Beginner
  • 278 Views
  • 2 replies
  • 0 Helpful votes

Hi,We would like to use object group in our PIX configuration. Can you please let us know what version of software we need to upgrade the PIX to achieve that? Currently we are on version 5.2(5).Thanks.

pokwan by Beginner
  • 358 Views
  • 4 replies
  • 0 Helpful votes

We have a Pix 506 that has a VPN connection to a PIX 520. There is one client on the 520 side that loses the ability to connect to the data server on the 506 side of the network. All other hosts can communicate accross. If we remote to a pc on the...

Is there a command on pix (v6.3.3) that would give a list of services (eg:http server) currently running on the pix? The "show service" doesn't really say much....thanks.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Recognize Your Peers