Resolved! IDS Network module
Does anyone can tell me if Cisco IDS Network module (NM-CIDS) can capture the vlan traffic, or it only can capture traffic going through it. If it can, how can I do that?
Does anyone can tell me if Cisco IDS Network module (NM-CIDS) can capture the vlan traffic, or it only can capture traffic going through it. If it can, how can I do that?
Hi,I am facing a problem in PIX Firewall, I have 515 in failover mode, one is acting as a primary and other is acting as standby.My Network isPC>>>L2 Switches>>>L3 Switch>>Internal L2 Switch>>>PIX>>>External L2 Switch>>>Router>>>Internet.whenever the...
Has anyone sucessfully implement command authorization on the PIX or FWSM? I seem to be stumbling on the enable authentication part. I can sucessfully authenticate a tacacs+ user, but when I try to authenticate the enable command, my tacacs server ...
Hey all ! It's is possible to evaluate some cisco securiy products ? I would like to test VMS to manage IDS (4210) alerts. Currently i'm stuck with cspm 2.3 and sensor version 3.0 and we dont have any smartnet contract so no acces to upgrade or pa...
Hi,the cco-autoupdate failes with the following notice:Alarm Status: Auto update failed using http://ftp-sj.cisco.com/cisco/crypto/3DES/ciscosecure/ids/ctr/updates/ctr-updates-2.0.xml. Please correct! (Failed to get http protocol response code when ...
Currently I can send mail but cannot receive mail from the Internet, if I remove the Pix and connect directly to the Modem/Router then I can SMTP in on port 25 and SMTP mail works fine both in & out.All we want this Pix to allow at present is:a) Inte...
Is there a way to generate a report on the number of shuns on a sensor or just to pull out the specific signatures you are looking for? Thanks,Shawn
The Trace from the internal network does not show the inside interface in the hops. The first hop is the internal Firewall and the second is the perimeter router connected to the Outside interface. Can anybody clarify on this ??
Hi,Are these compatible? If not, is there a general recommendation to stay with IDS 4.1 if using VMS?Thanks,Dave
I have a setup where an Avaya MedPro/CLAN is connected to DMZ with Avaya IP phones on the inside LAN, even with H323/225/323RAS fixups enabled and a access rule from DMZ to inside the IP phones dont get registered. When IP is enabled from MedPro/C...
How often do the signature updates come out?Is there a set schedule when signature updates come out?
Hi,I am unable to update new signatures to our IDS (IDS4215 and IDS4235) using IDS MC version 1.2.3. Previously we've been doing it through IDS MC and it worked fine. But nowadays this has stop working - we can still perform the job at the IDS MC, bu...
HelloI’m having a problem regarding my Primary PIX and PIX Failover unit.The primary (active) unit unusually getting standby status and consequently the PIX Failover unit unusually getting active status.No power interruption nor any configuration cha...
After many years of trying to do this we finally switched to a third party box to do QOS through our network since Cisco didn't seem to have an solution to do this.Is there any way, for the purposes of applying some form of QOS (LLQ or GTS/WFQ) for a...
HiI have Cat6509 with IDSM-2 in PwdDown state.How can I power up the blade ?Thanks in advance for your help
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-16-2025 04:21 AM | ||
07-06-2025 01:40 PM | ||
07-04-2025 01:59 AM | ||
06-19-2025 07:32 AM | ||
06-17-2025 01:07 PM |
User | Count |
---|---|
10 | |
7 | |
5 | |
2 | |
1 |