Hi, I noticed that there is a monitoring piece in my PDM that includes IDS. But when I looked at the histories, there wasn't anything there. Is there something special to make it work, or is it a separate piece of hardware ?Thanks
Hi, I noticed that there is a monitoring piece in my PDM that includes IDS. But when I looked at the histories, there wasn't anything there. Is there something special to make it work, or is it a separate piece of hardware ?Thanks
Can you please tell me what the DIP switch settings should be for the 2MB flash card? I accidentally changed them.Thanks
Could someone point me to a link(s) on Cisco's site to help me quickly explain, to a network manager, why the following scenario is technically not prudent from either a firewall or network architecture Other tasks prevent me from taking the time ...
Hello,i am new to the Cisco IOS and PIx products but a small company that i work for just purchased a Cisco PIX 515E to protect their network. i am a microsoft person so i am looking for a little help and insight. Right now, dont laugh, they have M...
hi folks! I understand that you can load the PIX IOS on a 1720 router and turn it into a PIX firewall?. Is this true? If so, how can do this? My 1720 has two interfaces.many thanks
I am in the process of upgrading my PIX from 6.1 to 6.3. I would like to know of any issues or problems I may run into when doing the upgrade? Any thoughts would be appreciated.One more thing. Since I dont have a contract with Cisco, I want to get...
Hi all,I need to config a tunnel with a costumer that has an ADSL connection that changes your IP address every time he connects on internet.How can I config the PIX Side ?? On the other side that is an SonicWall appliance.
Hello...We are looking to install both IDS and PIX components on one server. I was reading some of the items in the forum and was given the impression that it would be better if the two were split and installed on different servers. Can someone ple...
Anyone has a recipe to make it work ?Edy Rojas
am new at this.Is it possible to configure a Pix at one location between 2 sites? Allowing the other location to be trusted. Are there issues? If possible, what is the best config setup for this type of situation? For example - I have an office A...
Dear ciscoer,Any sample config PIX connected to the Internet with Router. The router using the IP legal and router's ethernet 0 using 192.168.0.xxx. PIX ethernet0 using 192.168.0.xxx and the PIX's ethernet1 192.168.1.xxx. Where should I NAT the IP le...
We are using a parameter interface PIX 520.Problem is that here.1. Already defined a static entry static (inside,outside) 203.125.152.243 172.16.206.21 netmask 255.255.255.255 0 02.want to allow a WAN link with IP's 172.17.0.0/16 to pass through PIX ...
its possible to balance several wan links. 2 situation, one if de link belong to the same ISP, 2 if the links belong to several ISP.My question is, can we do that?
I am a cisco firewall beginer .I have a problem with configuration of cisco 501.I have 1 public IP and i want redirect ports in more internal IP with the NAT.Is it possible?How Can I do?Please Help me!I thank you in advance.
Hi,we have a PIX 515E with 6.22 running. Does this software support SNMP v2 ? PIX doesn't doesn't reply back to SNMPv2 queries, however SNMPv1 works fine.Also, is it possible to in PIX to get the number of hits for a particular ACL Rule ? E.g. Number...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-22-2025 09:48 AM | ||
07-16-2025 04:21 AM | ||
07-06-2025 01:40 PM | ||
07-04-2025 01:59 AM | ||
06-19-2025 07:32 AM |
User | Count |
---|---|
10 | |
5 | |
4 | |
3 | |
1 |