Network Security

I have a PIX 515e with 6 interfaces (5 in use) - inside, outside, dmz, dmz2 and vpn.I am unable to telnet (or anything else) from dmz2 to dmz or dmz to vpn (possibly other combinations), but I am able to get from inside to anywhere or outside to anyw...

I have seen several individuals trying to sell a PC running the PIX IOS software on ebay. Is this possible? It sounds odd but I guess if you could get compatible drivers for the hardware its do-able. I am curious if anyone here has seen it, or tried ...

How can I integrate 3rd party antivirus platforms with PIX firewall ? Also I want to know about what Antivirus softwares are supported with the device?

I have PIX 515 with Software ver 6.2 I use the static command to map an internal server to outside real IP :static (inside,outside) x.x.x.x 192.168.10.10 netmask 255.255.255.255 0 1with access-list as follows:access-list 101 permit ip any host x.x.x....

Hey All,I was wondering if I change the MTU on my PIX to a lower number, does that take effect once I save that change or do I have to reboot the PIX?TIA

I am fairly new to PIXes; therefore, I need some help.I have read a lot of resources on PIXes. However, I can not get the firewall working in the basic NO-NAT transparent mode using nat 0. The main problem is that all cisco literature assume that Pix...

Recently we upgraded to CiscoWorks CD 5 V1. Cat4000-IOS devices are now supported in RME and CM. But in CM Topology Services the Cat4000-IOS devices are not seen as members of their own VTP domain. Instead, each access switch behind the Cat4000-IOS f...

I have a PIX 515 that displays one line of odd ASCII characters at boot then the PIX does nothing after that (does not respond). Tried to change console settings but to no avail. Any ideas?

I found the following entry in our PIX log: "...May 04 2003 02:24:49: %PIX-3-211003: CPU utilization for 10 seconds = 48366748%" According to Cisco docs, this message displays if the CPU utilization is over 100% for 'x' number of seconds and the numb...

I found the following entry in our PIX log:"...May 04 2003 02:24:49: %PIX-3-211003: CPU utilization for 10 seconds = 48366748%"According to Cisco docs, this message displays if the CPU utilization is over 100% for 'x' number of seconds and the number...

Hey,I tried to install 6.3 on my pix515e from version 6.2.1 and it just killed it. It repeatedly failed over about every minute and had no access from inside out on one of the interfaces. when it was up for the minute, my outside in rules worked fine...

Hello,i am connected the server behand the firewall..firewall ip address -outside - 64.170.x.1 inside -192.168.1.1IIS server A -ip address inside -192.168.1.2 outside - 64.170.x.2above server working fine and also i have IIS server B ip address -64.1...

We have 2 new staff that aquired tablet PC's running XP. (Compaq) When we go to set up the VPN client, we keep getting wrong OS type. We have tried every version they have listed out there and even got them to give me special access to older archived...

I am configuring several PIX 501s for Home Users using Cable providers as their ISP which uses DHCP. The central firewall is a SonicWall Pro 330 and can only take a 0.0.0.0 for when the IP changes for the IPSEC Gateway address if using Aggressive Mod...

I have a PIX firewall in which I wish to authenticate outbound connections for slected users of SSH & FTP against an internal AAA server, using TACACS.Is this functionality supported ?I have created an access list to match the traffic SSH-Tracker .I ...