We have a pair of 2140 FTDs running 6.6.1 that are managed by an FMC running 6.7. We'd like to upgrade the FTDs to later firmware, but can't at the moment. We're in the process of phasing out some ASA 5505's that are running site-to-site VPN tunnels,...
Searching around gave me nothing usable for this rather mundane question:how do I hide the source/dest SGT columns when viewing a policy?platform details are :-Model Cisco Firepower Management Center for VMWareSerial Number NoneSoftware Version 6.7.0...
How do I export my Firepower 2130 running-config to tftp server. From the FXOS CLI I entered copy /noconfirm tftp://x.x.x.x/etc. This command attempts to load from the tftp. What command copies to the tftp?
Hello everybody,our customer has a ASA5525 with Firepower Module running OS rel. 6.6.4. Our monitoring generated a warning because the swap usage reached 90%. The Health Monitor of the module in the FMC has still no red bubble yet. When I login to th...
Hello everybody, our customer is running FMC rel. 6.6.4 and Firepower 2110 and Firepower modules in ASA5516-X,all are running rel. 6.6.4 too. Now they need to query the interface utilization by SNMP. This is running fine for the FTD but there seems t...
Hi, I try to upgrade IOS for my ASA 5520. I did not find any OS for it in cisco website. Can I use asa9-14-3-13-smp-k8 which is for ASA 5525 for my ASA 5520? Note: I tried to transfer file from my laptop to the ASA 55520 using ASDM, but it fail. That...
Hi, I have a ftd with fdm working for vpn ra services (anyconnect). I would like to know if the following sentence is permit:route inside 0 0 gateway tunneledDo you have any suggest please?. I need to send the traffic for full tunnel to the another d...
I've got a Firepower 1010 set up (FTD via FDM) as a remote VPN device and I am unable to see devices on the LAN when I connect to the VPN. The device is connected to the LAN via the Management interface, where it is automatically assigned an IP addre...
Hello, Has anyone tried ro pass SMB or FTP/SFTP thru the 1000 series or 2000 series FTDs?Looks like performance is quite low - even with bypassing policy and fastpathing all traffic.Does not even hit the 1st rule which is any any for testing.No issu...
Dear community, I have configured a subinterface (ip addresss, vlan) on a parent FTD interface. The connection goes to a switch trunk port. For some reason there is no connectivity between FTD and switch. When I remove the subinterface and configure ...
We have two HA pairs of FPR1140's running FTD code and managed by a virtual FMC. They are all running 6.6.5 code.There are some FTD platform SNMP settings pushed to all the FTDs as we monitor these with another monitoring platform.We are monitoring ...
-I'm implementing an FTD Native instance (created on a 4110 Firepower Appliance) in an Firepower Management Center virtual (FMCv)-Currently I have an ASA-5585 with Firepower Services deployed in the same FMCv, I already added the FTD to the FMCv and ...
Hi,I'm looking into a issue where no connection events are shown in the FMC event viewer despite the configuration of the ASA and FMC looking good:ASA5515 running 9.12(3)12SFR module running 6.4.0.9FMCv running 6.4.0.9---Service policy is configured ...
Hello, I wanted to identify the machine that tried to download malware.I found the event in firepower management center but don't see details about the machine for which the action was blocked.The only details regarding client is: Client - Android br...
Hello all, I am following this article here: https://www.cisco.com/c/en/us/support/docs/security/asa-firepower-services/118644-configure-firepower-00.html I am attempting to install Firepower services on my ASA 5515-X. The exact image I am using is ...
