Hello, We would like to upgrade our Firewall from 9.1(2) to 9.6(4)12 and we don't have any support contract with cisco. Are there any risk to upgrade a firewall without direct support with Cisco ? And what is the upgrade path to proceed ? Thank you
Hii have FTD 4120 appliance , i use smart software manager satellite enhanced edition server for licensing in my Network.so my FTD is not connected to internet , and it uses satellite server for smart licenseI created token in satellite one years ago...
Hi, what is the correct way to configure the FTD 21XX so that the internal clients can use FTP on external ftp servers. I know that on ASAs we had ftp inspection that worked but i have hard time to find out how to configure the Firepower. I see tha...
HiI have one Asa 5516 up and running with Firepower Services (the firepower is a virtual server). I´m going to install an other Asa so they are in failover Active Standby and don´t really know how to manage Firepower. i hope somebody can help me, th...
Howdy folks - I've found myself in a position where I am trying to deploy a configuration change from the FMC to one of our FTD firewalls. The change it self is totally aesthetic (changing the name of an object). The deployment ends up failing with ...
Hello, I am somewhat new to Cisco so I apologize if this in the wrong forum. I am attempting to replace my CenturyLink modem with my ASA 5515x. I configured an interface using PPPoE and the credentials they provided. I also put the public IP addre...
Hi Guys,Please help, I am trying to upgrade my FXOS but I am failing. the Chassis 1: is stuck in Upgrading Status for days already.FP4100 /system # show firmware monitorFPRM:Package-Vers: 2.8(1.125)Upgrade-Status: ReadyFabric Interconnect A:Package-V...
I was reading one of the threat reports from our FMC and nearly all of the high impact threats were blocked however I saw two that read "would have dropped" under the inline result column. Anyone else experience this and is it just a cosmetic bug or...
Hello, I have a FPR-1010 with ASA 9.13I have two ISPs and I would like to use them simultaneously to benefit from the aggregated bw. How will I accomplish that? Regards, Konstantinos
Hello Cisco Community, I'm facing a problem in my Anyconnect setup: Context: VPN connectivity based on Cisco Anyconnect client 4.9.01095 + Cisco ASAv 9.12(4)7Problem:my setup requires split tunneling to exclude cloud services from the VPN tunnel and ...
Hi, I have a Cisco ASAv configured in GNS3. I am trying to configure the duplex setting for interface GigabitEthernet0/0 and I had configured the duplex as well and now when I run "show interface GigabitEthernet0/0" I am seeing the below output. Inte...
We have 1 asa product and fwsm product. fwsm-asa ㅣ syslog server It has this configuration. While sending syslog from fwsm to syslog server, asa set the policy to block fwsm syslog. But still fwsm is sending logs to syslog serve...
Hi, I am troubleshooting a VTI from an ASA to and IOS so I am starting with a non protected tunnel to rule out crypto. As you can see below the status and protocol are both down. I feel like this is because of "Mode: invalid! IPsec profile: Not defin...
I need to deploy an ASA 5500 series Firewall inside a small office .Online I read about that best would like to put a L2 device, a switch, between the Router and the ASA.Something like this: If this would be the best way for traffic flow and control,...
Hello everyone,Please consider the following example:Radius-server------Router port2-----port2-SW-port1---work stationAbove, we have:SW with dot1x enabled on port1. This will ensure only authorized work station can connect to network. But if some one...
| User | Count |
|---|---|
| 14 | |
| 12 | |
| 7 | |
| 4 | |
| 3 |
