Hii have UCSB-5108-AC2-UPG with 4 Blade ( UCSB-B420-M3-D ) and i want to running VMware V-SAN.so which version of V-SAN my servers support and i can run?and how can you leading me ? do you have any document? or link?
Hii have UCSB-5108-AC2-UPG with 4 Blade ( UCSB-B420-M3-D ) and i want to running VMware V-SAN.so which version of V-SAN my servers support and i can run?and how can you leading me ? do you have any document? or link?
Good Morning! I'm having some difficulties regarding our new Nexus 5020 switches. We have two of thse in which are connected to multiple2k models (which are being used in the Top of Rack). We are currently utilizing the 4.1(3)N1(1) version of ...
LAN, Data Center
Hi! Have you ever experienced in HX deployment, installer was stucked at starting. WE're currently adding a node in a cluster and We're using the same installer we used in creating the cluster. new node is the same as the existing nodes.
I have a brand new HX 3-node Edge cluster built with 4.0 but when I login to HX Connect, there is no Upgrade button on the left of page...Screenshot below.Is it because the version running is the latest already? The cluster is healthy.
After multiple attempts in Hyperflex Connect with correct password. The login is throwing this error. Though, I can login to storage controller via CLI. Is there any way to reset/kill those sessions?
Any reason to install DCNM if fabrics are set to nbm-passive and the third-party Broadcast controller uses APIs exposed by the fabric for flow control, mcast management, etc.? Does DCNM bring any toolsets for Cisco IP fabrics used for Media workflow ...
I need to know if i have 3 nodes HX240m5 and i need to add extra node , the extra node it must be with the same CPU and RAM ?
I have replication Network config failure on 2 clusters Cluster-1: Failed to post the Replication Network jobHX does not even touch UCSM or Vcenter , I am using HXDP 35.(2d) Cluster-2: [137] : Configure Bandwidth on Nodes - Failure: Error: Failed to ...
Hi ,I am working on DC evolution project in which need to connect two DC 's via border spinePlease provide any related document for deployment and configuration purpose.
what are the requirements of VxLAN MULTISE?from what my investigation i discover that physical interface is needed for the for port that will conect to the other site but is that really necesary or can it be a subinterface?and is there any other thin...
Hello, i would like to know how to install virl for my company ? what are the hardware prerequisites that i need to do it?
Hello, In the existing setup, I have VLAN-3 for both physical and virtual servers. Once ACI comes into the picture is it possible to use the same ENCAP for both PHY and VMM domain in same EPG?Example - Using encap VLAN-3 static binding and VMM domai...
Need some clarification on BGP use case in a dual-homed scenario. In the dual-homed scenario depicted below, is there any benefit of using BGP to advertise public networks? Configuring default routes with different metrics should suffice. Please advi...
I have network scanning tools that will give me information about my devices: MAC address, operating system, etc.. Is there an easy way to identify my Cisco switches: ideally model, type, series, etc.?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-26-2024 05:05 AM | ||
07-22-2024 05:43 AM | ||
07-17-2024 05:59 AM | ||
06-24-2024 10:07 PM | ||
06-23-2024 10:40 PM |