Ask Me Anything Event Thank you for joining us for the Expert Insights Series on ACI & NDI: Empowering Data Center Excellence! Our Customer Success Specialists Cody Albea, Peter Nalley and Manuel Valasco will be available from May 15, 2025 through...
Hi All,can I ask you for help in clarifying the definition of port types in Nexus Data Broker application?There is possible to set port type as Edge Port-SPAN or Edge Port-TAP. Documentation says that:- Edge Port-SPAN — Creates an edge port for incom...
We had a hardware failure which in turn caused are Call Manager and Unity to become corrupt. When attempting the install we are running into the follow error message. "/opt/cisco/instll/elm_server/scripts/elmdb_prepare install PostInstall 11.0.1.229...
Hi guys, I would like to enable the jumbo frame support on my N5k for specific SCSI trafic. I've read we can't do it per interface but only on the system itself : policy-map type network-qos JUMBO_MTU class type network-qos class-default mtu 9...
Hi! This might be too easy for you guys, but i'm goin nuts here. I have two N9K set up in the datacenter. I am able to login to the console when directly connected with my laptop. But i can NOT login when i'm in the office and try it over the termina...
Dear coleagues, I have a customer that uses N1K, N2K, N5K and N7K in a traditional architecture inside his datacenter. Today, they are implementing a VXLAN BGP EVPN Fabric using N5K6 and N7K, and I need to recommend an SDN solution integrated with CA...
I have reset my SGE2010P for factory default and IP and user and passwords are as normal 192.168.1.254 admin / admin The following page is as attached and I am unable to do anything else
Hi All, So very new to Cisco so please be gentle! We have inherited a N3K-C3548P-10G switch with a dozen or so SFP-10G-SR sfp modules. I have performed a write erase on the box and configured as fresh. I am trying to get a link between this 3548 a...
Hi, I recovered a Cisco MCS 7816-i5 with the original 4gb of DDR3 ECC ram. For my purpose, it's not enough, so I checked the data-sheet and I bought 4 modules of Hynix 4Gb registered PC3-10600 DDR3 1333-MHz dual-rank dimms. The system worked flawless...
Hi everybody, I thought that vPC wasn't available on layer3 interfaces. But I've read a cisco doc about vPC and HSRP => http://www.cisco.com/en/US/docs/switches/datacenter/nexus5000/sw/mkt_ops_guides/513_n1_1/n5k_L3_w_vpc_5500platform.html I've at...
Greetings, I have a configuration as per the attached diagram that has fibre distances of approx 20km. Initially we configured a Layer 3 core between Data Centres using dark fibre and DWDM optics, and this has been working for several months. To fa...
In the process of deploying Cisco Nexus Fabric Mangers and I could not locate any information regarding a highly available setup (active/passive) configuration where two NFMs are running, one active and other passive. Any information is appreciated.
Hi, We have a new Cisco 9396 Fibre switch. It is running fine but don't have web access. The http services are running but when I tried to access with IE/Chrome/Firefix ...I get "site can't be reached". Is there a special setup for http managemen...
Hi I am migrating a small DC away from 6500's onto a pair of Nexus 9500's. The customer has overlapping VLAN's between different environments and we are looking to consolidate into a single fabric while having dual running between the 6500's and 9500...
Hello Experts, As question from interview panel, how to clear some lines from device logs without clearing entire logging. I am not sure how to remove some lines, i have seen if we want to clear, it will clear entire logs in IOS, NXOS, ASA logs. J...
This Cisco one bundle C1F2PUCSK9 is for 9 servers ?
