R1#show runBuilding configuration...Current configuration : 2418 bytes!upgrade fpd autoversion 12.4service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname R1!boot-start-markerboot-end-marker!l...
Currently, I am working off of a .bin file for phone systems using Arris and Docsis MIB's. A client wants to switch to a Cisco setup, and I am having difficulties finding the equivalent MIB's for MTA devices.The MIB's that we are currently using for ...
Hi. I took CCNA courses over 15 years ago. I have a Cisco C1111-8PW router and cannot reach the outside world. Interface GigabitEthernet 0/0/0 is connected to an ONT and I've temporarily enabled DHCP, as a client, on the interface. The interface...
Hi There, I have couple of question related to NAT. 1. I have a requirement to NAT the specific traffic receiving on the interface to be NAT to the interface IP itself. I have simulated this with the below syntax. ! interface GigabitEthernet1/0 ip...
I know that 2950 switch can support up to 64 STP instances,but how many instance for 6500?A situation is I had cerated vlans exceeding 64 on 6509 works as vtp server,it's ok with 6509,but there're many vtp clients which are 2950.The running-config sh...
Hello Cisco Community, I am currently on a Internship at an college, and gotten a assignment to update the firmware of a cisco 2611 router.after i got my hands on the firmware and fired up the tftp server and attempted to push the upgrade to the rout...
Hello, I work for ISP. We already have two /21 IP blocks on our network. I want to add one more /22 IP block on my network. I don't know if that is possible. How many IP blocks can we add to our Network..Any suggestions??
Generic question that I'm sure would have been answered, but the old Cisco tools don't work any more. How do I check which commands are supported on a particular hardware platform? For instance before I buy the equipment, how can I check that a certa...
Hello, I have this customer who use a public IP address range(for example, 100.100.100.0/24) in their internal LAN. They have assigned these IP address to servers, laptops, printers etc. And these are NATed(PAT) to firewall outside interface IP when...
Hello,I've found a similar topic on this forum, but no solution was provided inside (link to old similar topic). Short description of the issue:Packet Tracer 7.2 is oversized: the icons are too big, it looks like the whole interface of the software i...
Hello everyone,Can anyone explain to me why we need a router to ping PC's that are in different vlans?Or better yet, I have doubts in behavior about:1 - What happens when I ping to PCs that have the same VLAN?2 - What happens when I ping PCs that hav...
Is it a bad form to name access-list, class-map, policy-map all the same or it is encouraged? Similarly, there are several crypto related configs like authorization policy, authentication policy, keyring, etc that could also share the same name.
I have been giving the task of moving are ASA into VLAN 995, change inside IP and Move all L3 sub-interfaces to a single, trunked L2 port-channel. All future L3 interfaces will be housed upon this new L2 port-channel. I have never done this and would...
Hi, I have to design an enterprise network. The topology is as below AS1, AS2 ---> Access switches (L2)DS1, DS2 ---> Distribution Layer Switches (L2 and L3)CS1, CS2 ---> Core routers 1. 2 Vlans viz. 100 & 200 are to be used in access layer. Vlans ...
I am trying to figure out why the SLA is flapping between 10.1.2.2 and 10.1.3.2 every 15 seconds. The delay is below 60 Milliseconds and it still flaps to 2nd static route 10.1.3.2. Also, even if I shut down the interface on R2 , 10.1.2.2 still shows...
