Hello, The attached design depicts two solutions: The first one shows a pair of NX9Ks configured in a vPC and uplinked to a single upstream C3560 switch using a bundle or 4 physical ports to form a L3 port channelsThe second design shows a pair ...
Hello, The attached design depicts two solutions: The first one shows a pair of NX9Ks configured in a vPC and uplinked to a single upstream C3560 switch using a bundle or 4 physical ports to form a L3 port channelsThe second design shows a pair ...
Hello all. I have a question about the enterprise network design. I have changed my job and here i have seen a couple of new design implementation which was done by previous worker. I do not have to much experience so i haven`t seen so much enterpris...
There is no Assurance client data in DNAC for wireless. (Cisco ONE - 3504 Wireless Controller)
how to load ios into 3745 if flash ios accidently erased? Router went into rommon mode. Thanks
Hello, Apologies if this is in the wrong location. I work in the public sector and so our user base is pretty big. Currently we use locally significant VLANs per switch cabinet with port-channel uplinks to the Distribution layer. We are thin...
Hi, networking is not my speciality, hence I'm struggling to get this to work.I want to create a VLAN for guest wifi access. I don't want anyone on this VLAN to access anything other than the internet. I am using a pair of Nexus 3548. I have creat...
Hi allDoes anyone know of free utilities out there that enable you to flood a WAN link for capacitytesting? For instance Solarwinds Engineer Edition (found at www.solarwinds.net) does have a tool called "WAN Killer". This toll is pretty good but I'm ...
Hello All,I'm a beginning Network Specialist and just thought I would throw this question out and see if I can get some answers. Well I want to know how I can use CDP to discover our network topology so I can create layouts and diagrams in Visio or ...
How many EIGRP processes can a MSFC2 supports sumultaneously ?I didn't find any written doc about that?Thanks in advanceBest RegardsFabien.
Hello experts, i've benn reading many articles about how to setup NAT but didn't find an answer for my "special case" with natting across vlans but not to the internet I want to do the following: I've three vlan interfaces - if1 has ip add...
Hi , i have to connect three routers in the same bgp "as" to another router in another bgp "as" but, when i run show ip bgp summary the connection from one router appears as down to the neighbor in a different "as". This is my config for the routers:...
Hallo, How can one configure dyim=ng gasp feature on Cisco 2811,2911 and ASR-1000 routers? Regards, Joy.
Thank you Julio, but is just device administration with radius, what I really need to do is to configure a Mikrotik router and that authenticate with ISE server, so I have Cisco ISE Base License to add Cisco network devices with TACACS, but Mikrotik ...
I am testing traffic for wireless devices having AP and SU, traffic was going fine for firtst time after booting up the server then it's start dropping of packets even for low traffic in KB, also instead of AP and SU i tried with connect a self loop ...
Hello, I have several (about 40) BGP peers to which I applied a simple filter-list just like this: neighbor 10.20.30.40 filter-list 10 out ip as-path access-list 10 permit ^$ ip as-path access-list 10 permit 12345 so that to 10.20.30.40 only pr...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM |