Hello, I have a few new HP Proliant Servers with two FastEthernet adapters with HP's NIC Teaming. What would be the best load balancing solutiong in pluggin these servers to 2-3550's which will then be load balanced with two 4503's? I hear...
Hello, I have a few new HP Proliant Servers with two FastEthernet adapters with HP's NIC Teaming. What would be the best load balancing solutiong in pluggin these servers to 2-3550's which will then be load balanced with two 4503's? I hear...
hi,I need to configure an e1 pri to make simultaneous ddr connections to a T1 in the US for 24 of its channels and to another site in Europe with the remaining 6 channels.Can anybody assist with a relatively simple solution to this scenario.Many than...
Hi everyone!This is my first post here as a minuscule CCNA!I am from a Transmission background and know the full make up of an E1 Frame as far as TS0 & TS 16 and the 30 data channels.I have x2 2501 connected back to back.One is DCE and one is DTE.I a...
How to configure subinterface for load shareing in G.703 controller
Dear Sir,We have a hub and spoke WAN network with on central location and 7 remote locationAt central location we have LAN subnet as 192.168.1.X/24 and 10.10.1.X/24At all remote location we have LAN subnet as 10.10.2.X, 10.10.3.X/24 etc..We have AS/4...
Can someone tell me how to setup the ability to only allow a certain network to access one IP address.I have a Cisco 3640 with two ethernet interfaces. I want the network on ethernet 2 (10.30.30.0) to only be able to access one IP address on etherne...
Hi,I use a VWIC-1MFT-E1 interface and see output errors when I do a "sh int". At the remote side the same amount aborts occur. The Telco guys checked the line and see also that the router sends illegal sequences.So what could be the reason for an out...
I have just sync'd the ANI db with RME and I only see the IP address in RME. I have read a previous conversation stating that you must use DNS. Is it possible to only use a host file instead of DNS?thanks much!!!
We have a 3640 NAS Server with Analog Modem Module on our Network for Dial-in users. For a long time the speed of connection to this equipment went of 40K, but for a time the speed has gone down to 32K. We believe that this descent of speed is due to...
Hi,There are 4 classes in the AF mode (from 1 to 4), and for each one 3 level of drop.Can someone tell me, which class will be droped first, 1 or 4.thks for ur help
Hi All,I'm trying to work out Cisco ISDN router,which can support IP/IPX/IPSec and Dialer profile / Backup with two ISDN port.Can you please let me know any cisco 800/1700 series router, which can support with 2 ISDN port 1 ethernetThanks & Regards S...
Hi,I'm having persistent CRC errors when I connect anything to one of my CAT 4006 switch ports(WS-X4412-2GB-T line card). All connected switches report rxCRCAlignerrors and users lose connectivity to Servers and the Internet. FCS Rcv errors pile up!!...
We have just had a big spanning tree loop between our two core switches, we are about to enable Spanning Tree Portfast BPDU Guard Enhancement but want to map the current port states. What is the best way to do this, to see which ports are root, desig...
Excuse me , Who can tell me where to find all cisco products' output electric power? Thanks
We have two main sites connecting to a customer network through PIX 515s. The PIX 515s sit behind Cisco 2600s which are configured as GRE tunnels terminating at the customer Cisco router. The GRE tunnels are transmitting and receiving OSPF LSAs...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM |