Hi, please is there a way to find out what ports on a catalyst C2950 were not used frequently in a time period? I mean for example a monitoring software or a summary report how many connections were made last week or so?Thank you very much!
Hi, please is there a way to find out what ports on a catalyst C2950 were not used frequently in a time period? I mean for example a monitoring software or a summary report how many connections were made last week or so?Thank you very much!
Hi, please is there a way to find out what ports on a catalyst C2950 were not used frequently in a time period? I mean for example a monitoring software or a summary report how many connections were made last week or so?Thank you very much!
hello,I use a switch 2924M, with an interface ATM WS-X2961-XL . With the boot I do not see in the show version the interface ATM. when I return in configuration mode, I nothing commands on the level interface ATM. I think that I am not with the g...
We have interest to purchase IE2110 Configuration Registrar for our network, the reseller write us about Type A device license pack and Type B device license pack, but they do not know, what is this. I can't find any information about it throught www...
Is it possible for a single port on a Catalyst 5500 to be a member of more than one VLAN?For example, the normal command syntax is:set vlan 2 2/15But, I would like port 2/15 to be a member of both VLAN 2 and VLAN 3.Is this possible??? If so, please p...
I have a 3550 XL with the Enhanced image as a Core switch in our infrastructure. I have 10 2900/2900XL swtiches each directly connected to it. I want to configure each switch as a Vlan and IP Subnet. I want each of these Vlans to use DHCP from our ...
Hi, I have just gone through the nightmare of having a corrupt bootldr file and am a little gunshy at this point after the time spent correcting.I want to blow away the config in the Cat6 and start over, but doing so wil remove the "boot" commands in...
Hi, I have a CISCO series of CISCO : 2500 seriesIOS version : 12.2(6a)I configured cisco as DCE and enabled qos-autosense and traffic-shaping on CISCO serial interface. When I am creating a new PVC it is not sending qos-parameter related information...
I would like to install a new T-1 into an existing 2600 router that has a 64K ISDN already installed. The router passes mail to an Exchange server. Can I not have both the T-1 up and running while still recieving/sending mail to the Exchange server o...
I have a 7206 attached to a port on a Cat4006 and I'm bridging on the 7206 int fa0/0 to extend a vlan from across the country to my Cat4006. However at some point I need to attach more devices into the Cat4006 than those that are extended across c...
Hello,I would like to know if it is possible to have following configuration:CISCO 828 routers in branches (10 Pcs), and CISCO 3661 router with 10 G.SHdsl WICs in the central office with back to back configuration to each branch office router. The di...
which ieee 802.3 encapsulation is the default for cisco router?And if i want my router to run over ethernet by using snap encapsulation ,which command should i used?
WE want to avoid using a hub.
I user Win2000.I want config Router to user dialup thru router to join domain of win2000
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |
User | Count |
---|---|
2 | |
2 | |
1 | |
1 | |
1 |