Hey. I am unable to download packet tracer. I am not even able to login.On logging in , its just liading and loading....What to do now ? Can you please help me?
Forum Posts
Hell-o. I am trying to configure an ASR 1002-f with IOS-XE Version 15.4(3)S6a for two point to point VPNs. I am currently running a Cisco 891W but need the added WAN throughput of the ASR. This is my configuration on the 891 which works flawlessly...
Hi,I am really new to configuring switches.We have a cbs350 stack (core) with multiple (8) VLANs that are configured with native VLAN statements, for example,interface GigabitEthernet3/0/3description "Test Network"spanning-tree link-type point-to-poi...
Listen: https://smarturl.it/CCRS9E35Follow us: https://twitter.com/CiscoChampion In today’s hyper-distributed world, ensuring a secure and flawless application experience for remote workers and offices is now paramount. Secure Access Service Edge (SA...
Hi.Hope you are doing great.I was working in a NCS-6000 and suddenly I realize that when I type the command CRP/0/RP0/CPU0:NCS#admin show install activeTue Sep 13 17:25:43.962 CDT% No entries found.Does not show the smus, but if apply the command:R...
To briefly describe this company has this main product, drones, who is revolving around in testing, management and mass produce TypeSpecificationHQ/Branches* 200 sites, different sizes between 10 to1500 EmployeesDrone Landing/Staging Ports800 sitesLA...
Hi everyone,Recently had an issue where an interface on our ISR4221/K9, running version IOS XE Software, Version 17.03.04a, went down for a small amount of time causing an outage. The logs showed: 07:56:38.088 JST: %IOMD-3-MODULE_MESSAGE: R0/0: iomd...
Hi guys, I currently have some trouble with VXLAN.Currently I want to test a simple topology with 1 Catalyst 9500 as spine switch and 2 Catalyst 9300 as leaf switch as below: My current configuration is very simple:Underlay running OSPFOverlay ...
Hi all,I work with Cisco 867VAE, C881-K9 and currently C921.we use third party company from Japan to create the config for Cisco, then I do EZVPN zero touch to the cisco. This Cisco only use two port , 1 LAN and 1 WAN.Lan is connected to user Comp...
Looking for actual documentation that correlates the following assumption on my part: AR1 - 8x5xNBDAR2 - 8x5x4 hourAR3 - 24x7x4 hourAR4 - 24x7x2 hour This is derived from comparing the options and prices: AR1 SD-AR1K-NC57C3MSAR LEVEL 1 NO SW SUP ...
Hello. I'm using Putty 0.63 to access all corporate routers (28xx, 29xx, 39xx, different IOSes) and stumbled into one common problem: if i launch some long running command like ping with many repeats or file operation then it runs for about 50 second...
Hello.We have an addressing plan developed for accessing networking devices. Because not all devices are running in L3 mode (and some of them are L2 by design), Loopback solution cannot be used.We have all management addresses defined as VLAN interfa...
Hi! I have a Cisco 7600 and recently experimented high CPU utilization. Thanks in advance.
We have an Oracle ZS5 with two controllers that operate in Active-Active mode that is connected to two Cisco 9300 switches that are clustered together. A single ZS5 controller has two ethernet ports configured as LACP that connect to a port-channel (...
According to the BGP best route decision, best route will be chosed base on the the the sequenceattributes ( Weight, Local preference, AS-Path, ). But I want to know do that attributescontrol the flow of inbound traffic or outbound traffic or both di...
