Other Network Architecture Subjects

I am currently programming two c2611 routers. I have both routers configured and in place. I have a computer hooked off of a Fast Ethernet Switch on the Remote side with a IP address of 172.18.1.10. I am able to ping the IP of the computer all day lo...

New security policy is calling for a long winded message to be displayedIOS 12.2.8 on all routers, CatOS 7.2.1 on switchesThanks

Hi,We use a uBR7223 with IOS v 12.1(11b) here. In order to test the new cable monitor command we connected a linux system running snort to the fastethernet port and issued the commands as per http://www.cisco.com/univercd/cc/td/doc/product/cable/cab_...

Hello,i have the following problem:i want to connect our cisco router with a MS-Client.Below you can see that the router should make a callback.If i dial the router, the connection goes up without callback andi don´t get any error messages.Cisco Inte...

I have some questions about V.8 Recommendation.I monitor the progress of the modems connect. I can get demodulated data andsignals from the line, and I try to get signals and data from hardwaremodem(USRobotics Courier V.Everthing) according Recommend...

If I want to run OSPF via tunnels and do a no passive-interface on the tunnelservercard (f.e. pos 7/0) will the tunnelinterfaces itself still be able to run OSPF or not?

Hi,i have a BGP speaking router, which has only VPNv4 adress-family enabeld.No IPv4 !1.) I am not able to force route-refresh or Soft Clear of a other VPNv4 neighbour.Is it a prerequisite to enable IPv4 - but i have no need to do this ( i only need V...

dot1q is a mono spanningtree...what does that mean ?Does it mean one instance of spanningtree per VLAN, per TRUNK, per switch ?????So if you had a switch with 10 trunks, trunking 10 VLANS, you would have 100 instances of STP ?Or is it one per .....He...

I would like to know what is the maximum value of Bc we can configure for a frame-relay map-class when using FRTS ? I am currently using 12.2.1a.Thanks for you support...

We have a MS 2000 Server, SP 2, all hotfixes, with an Intel Pro/1000 XT gigabit Ethernet NIC connected to a Cisco 2950 LAN Switch on the RJ-45 copper GigE port. We have the MS compatible HCL driver for Intel on Windows 2000 dated 5/06/02.At 100M/ fu...

I'd be grateful someone could provide some info on the following points I have about RTM Traffic Monitor.1/ if I select a switch port, choose the data link layer view, I get a graph of port no. v % utilization. O.K. If I now choose the Time menu, and...

I have 2620 rouer with 2 port ATM E1 card. This is connected to Alcatel MSP 7420 ATM switch. The router has another WIC card with 2 serial ports, one of the serial port is connected to VSAT modem and configured for V.25bis ( DDR ). How do I route the...

I have two routers. I would like router 1 to have primary address of 1.1.1.1, secondary of 2.2.2.1. I would like router 2 to have primary address of 1.1.1.2 and secondary of 2.2.2.2. I would like to have hsrp or vrrp for 1.1.1.3 with one box activ...

Hello,do anybody know decision the next problem:router#sh int f 0FastEthernet0 is up, line protocol is down...Description: connected to EthernetLAN ... MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 128/255, txload 1/255, rxload 1/2...

Hi,I need to connect servers over 2 type of module : WS-X6548-RJ-45 and WS-X6516-GE-TX.I know that on certain modules we have on the hardware "group of ports" (ex: perhaps 3 groups of 16 ports or 2 group of 24 ports...).Depending on this, I have 2 qu...