Other Network Architecture Subjects

Hi thereI hv been trying for the past one week to successfully install Ciscoworks LMS with HPOV NNM6.1/2 with various permutation & combinations. Atlast, I managed to Install CiscoWorks2000 second edtition CD one and HP OV 6.2. But now my Ciscoworks ...

I have catalyst 5505 with 2 supervisorIII card configured as standby with firmware ver 3.1(2) and CATOS cat5000-sup3.4-1-2.bin with 32MB DRAM and 8 MB on board Flash. I tried to upgrade image to cat5000-sup3.5-5-10.binimage is uploaded properly accro...

I have a 2924 that won't boot up. I type in boot, and it loads an image file, then when I try to configure it, and do a "wr mem" it gives me an error,>>>nv_done: unable to open "config.txt.new"[OK]NVRAM Verification Failed<<<<<what would stop me from...

Hi,I have the following senerio, Head office and Branch Office and they are connected through 128K leased line using CISCO 3620 routers. I have a dump terminal at the Branch End and is connected to Async Port on Cisco 3620. Unix Server is connected o...

ProblemI'm about to set up an ATM connection. FactsAt present I have numersous frame connections that I'm going to conglomerate onto a single ATM connection. Question What information do I need to resolve this issue.please reply to cdetirado@campusmg...

I picked up a few of the 50 or so WS-C1201 swithces a large California aircraft company retired. They must have done a clear config all to wipe out nvram, but also an erase all to wipe out the ios off of flash. I have the ios to reinstall, but cannot...

Thank you for any help you can offer. Remote site was running fine one day the next the line protocol goes down and I haven't been able to recover it. basic classless config, s0 and fastethernet int's configured and ppp is in use. Line protocol on ...

BEG YOU!!! PLEASE!!!! HELP!!!! I'M BEGINNER!!! WHO COULD HELP ME TO UNDERSTAND WHAT MEANS AND HOW CAN I INTERPRETE THESE STRINGS ON MY CISCO: 1.3.6.1.4.1.9.2.2.1.1.44 - locIfipInOctets IP 1.3.6.1.4.1.9.2.2.1.1.45 - locIfipOutOctets IP 1.3.6.1.2.1.4.4...

Thanks !Regards, Anacelia

I aplogize if this is not the right forum for this, but can anyone recommend a good reference/learing book on frame relay?Thanks

Connected a CNT device as a STUN connection via Serial lines. The interfaces are both up, but on end has the DCD down. Traffic is flowing thru the interfaces and everything is okay, but I would like the DCD to go UP. Is there anything I can do to ...

2611 router with wic-2T sync/async cards connected to 3com Courier external modems with Auto Answer enabled on modems to allow dial in users to access network,the problem is that DTR sometimes goes low and this leads to failure of auto answer so the ...

We have an old 2500(68030) running v11.0(10c) software, we are getting attacks daily with ICMP to the point of denial of service. We have been told updating the router may enable us to prevent some of the issues, but have been unable to find update ...

I got couple used Cisco 2600/3600 routers from USA and I want to use them in China. Inside these routers, there are NM-1E2W, NM-4T, NM-32W, WIC-1BU, WIC-IDSU-56k4. If I want to use these existing NM to connect to network in China, could that be probl...

This dial-up line is a ISDN 64K and the remote site is using this ISDN for DDR backup for the serial line to the central office. The serial line goes down +- every second week for a few munitues so the ISDN is critical for network operation. The remo...