Other Network Architecture Subjects

hi, we need some ideas and we hope that we could it find here. in our case, we have two haedquarters. this two hq are connected with two wan-links. within every hq runs ospf between the hq´s run bgp. every hq has two local router that runs bgp one ro...

Hello,Is there any disadvantage of using secondary address in production network where those secondary subnets are heavily used.what are the disadvantage? Any info or link to a site would be great. ThanksFaisal Khan

I have a 3640 connected to a 2620 via a synch serial T1. The 3640 has a NM-2FE-2W with a VWIC-2MFT-T1. The 2620 has a WIC-1DSU-T1 (Part #'s should be right). The following link describes what I'm trying to do: http://www.cisco.com/warp/public/788/voi...

On 7206vxr, with IOS 12.1(5)T7 on a fastethernet with subinterfaces I have service policy that shapes the outgoing trafic, but shaping fails, it worked fine when the interface had't subinterfaces, but now classes match packets but shaping is not acti...

Does anyone know how to route between multiple paths (minimum of 2) by the use of Time of Day? I want to be able to have traffic route via path A during the day and at night, have it take path B.

Hi thereI hv been trying for the past one week to successfully install Ciscoworks LMS with HPOV NNM6.1/2 with various permutation & combinations. Atlast, I managed to Install CiscoWorks2000 second edtition CD one and HP OV 6.2. But now my Ciscoworks ...

I have catalyst 5505 with 2 supervisorIII card configured as standby with firmware ver 3.1(2) and CATOS cat5000-sup3.4-1-2.bin with 32MB DRAM and 8 MB on board Flash. I tried to upgrade image to cat5000-sup3.5-5-10.binimage is uploaded properly accro...

I have a 2924 that won't boot up. I type in boot, and it loads an image file, then when I try to configure it, and do a "wr mem" it gives me an error,>>>nv_done: unable to open "config.txt.new"[OK]NVRAM Verification Failed<<<<<what would stop me from...

Hi,I have the following senerio, Head office and Branch Office and they are connected through 128K leased line using CISCO 3620 routers. I have a dump terminal at the Branch End and is connected to Async Port on Cisco 3620. Unix Server is connected o...

ProblemI'm about to set up an ATM connection. FactsAt present I have numersous frame connections that I'm going to conglomerate onto a single ATM connection. Question What information do I need to resolve this issue.please reply to cdetirado@campusmg...

I picked up a few of the 50 or so WS-C1201 swithces a large California aircraft company retired. They must have done a clear config all to wipe out nvram, but also an erase all to wipe out the ios off of flash. I have the ios to reinstall, but cannot...

Thank you for any help you can offer. Remote site was running fine one day the next the line protocol goes down and I haven't been able to recover it. basic classless config, s0 and fastethernet int's configured and ppp is in use. Line protocol on ...

BEG YOU!!! PLEASE!!!! HELP!!!! I'M BEGINNER!!! WHO COULD HELP ME TO UNDERSTAND WHAT MEANS AND HOW CAN I INTERPRETE THESE STRINGS ON MY CISCO: 1.3.6.1.4.1.9.2.2.1.1.44 - locIfipInOctets IP 1.3.6.1.4.1.9.2.2.1.1.45 - locIfipOutOctets IP 1.3.6.1.2.1.4.4...

Thanks !Regards, Anacelia

I aplogize if this is not the right forum for this, but can anyone recommend a good reference/learing book on frame relay?Thanks