Hello,my 2620 hangs at the initial setup:-------------------------Cisco Internetwork Operating System SoftwareIOS (tm) C2600 Software (C2600-I-M), Version 12.0(7)XK1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)TAC:Home:SW:IOS:Specials for infoCopyright (...
Forum Posts
Resolved! Failing with simplest NAT config ever
I am using a Cisco 1921 with Gig0/0 and Gig0/1 interfaces on it. I'm trying to do something really simple, however it isn't working at all and I feel I must be overlooking something very basic. ip cefno ip source-routeip classless!interface GigabitE...
Resolved! Remote internet access
Hello Community I need to have internet access on my remote sites to monitor the power supply (a cloud based solution only),the remote site are in a rural city with no internet connexionthe idea is to have a remote internet access from the hub Router...
Hello, i have got two Cisco routers connect with HSRP configuration. On one interface of these routers i need change group ID due to change virtual MAC address. What is the best practise for this change ? I want to avoid outage on other interfaces.N...
Dears All I installed a new Fan tray( ASR-9006-FAN )to my box beside the first one ASR-9006-FAN -v2 for ASR9006 and i need to know what is the deference between the two versions and is that effect the service? 0/FT0/SP ASR-9006-FAN READY0/FT1/SP ASR...
Resolved! Ctrl-Shift-6-X combination for telnet
I can not use Ctrl-Shift-6-X key combination for suspending telnet connections. I'm telnetting to router A then telnetting to router B through A. In this case Ctrl-Shift-6-X key combination should suspend the second telnet session. But it's not worki...
Hi, somebody knows any email of Cisco Networking Academy support. it is very sad that is almost impossible any communication with them. Thanks
I am unable to gain access to the 1841 at the moment because I had disabled the password recovery feature. Break command doesn't seem to work. I followed this password recovery link without any luck. (C1841-ADVIPSERVICESK9-M), Version 15.1(3)T4, S...
Hi, We are migrating our network from the typical MPLS to a flat L2 network. Today, we have /30 subnets for each location and BGP across the enterprise, and our layout is hub and spoke with two hub datacenters. Due to new requirements, we have to se...
Hi, I am trying to configure an extended named ACL for this Router in packet-trace for an assignment and nothing I do seems to work. I am trying to get just one network to have access to FTP. The current commands I have are: ip access-list extended W...
I'm currently trying to configure the sg250-08 switch and have created 2 vlan, the default vlan1 (10.138.2.254) and vlan104 (10.138.4.254). inter vlan routing is enabled and i'm able to communicate between vlan and is working perfectly. The home DSL...
Whenever I restart packet tracer, It ask me to login and then continue. It doesn't start directly. It first prompt login page and then move furthur after login to the netcad academy.kindly solve my issue.
Resolved! Nexus 9000 temperature Minor alarm
hello,I have a Cisco Nexus 9000 sh environment temperatureTemperature:--------------------------------------------------------------------Module Sensor MajorThresh MinorThres CurTemp Status (Celsius) (Celsius) (Celsius...
Resolved! strange logs in sw IE5000
Hello. Someone recognizes these logs in a switch IE5000?I have seen old posts with old firmware versions in others switches that attributed it to a bug. But I already have a new version 16.12.03 %SYS-4-CHUNKSIBLINGEXCEED: Number of siblings in a chun...
Hi, I am trying to find documentation/design guides about configuring both Intradomain multicast routing PLUS interdomain multicast. I assume the common practice for intradomain is using Anycast RP but want to see actual guide for configuring interdo...
