I am having problems with the traffic I am seeing on my sniffing interface. I had the switch admin SPAN the traffic I wanted to the sniffing port but all I see is this:Using device /dev/spwr (promiscuous mode) ? -> * ETHER Type=8...
I am having problems with the traffic I am seeing on my sniffing interface. I had the switch admin SPAN the traffic I wanted to the sniffing port but all I see is this:Using device /dev/spwr (promiscuous mode) ? -> * ETHER Type=8...
Hi all,WE wrote a tool in perl and html that generates a config file for the 3002. WE upload the file and all works well with static and dhcp configs. But when it comes to PPPoe, our html takes the clear text pppoe password and populates the config f...
hello,I have installed Squid caching proxy server in my trusted site. I just want that when someone requests a web site from trusted, firewall send request to Squid. And noone, except Squid server, will use HTTP for webpage request. How can I do tha...
Dear Everybody, I'm not sure what i did wrong over the setup, but I was trying to access the PIX using the PDM, somehow i'm keep getting the error message after i type in the password, "Yor PIX image has a version of unknown. This version of PDM will...
Can I have a range of IP addresses for a single port in a access-list instead if inputting each one. If I can how do I do it.Thanks
Does anyone know the best way of finding out how long a user is locked out of a cisco router when they have exceeded the maximum number of failed telnet login attempts? I want to control:1. How many telnet login attempts are allowed before the user i...
Hi, I have a Cisco router running IOS firewall directly connected to the Internet. I am using Cisco Secure ACS running on a Windows 2000 server to administer my accounts etc... the real question is what software do I need to administer and report on...
We use ACS to authenticate users accessing the network devices and dialling in. The switches and routers are configured to use tacacs as the first method of authentication and then local should the tacacs be unavailable. We are implementing passwor...
I have one ids module installed in the 6509. I used the setup command to set the sensor's ip add :192.168.1.2 default gateway 192.168.1.1 . Then I set interface vlan 20 in msfc2, But the vlan 20 is down . I can't ping 192.168.1.2,What is the proble...
Can anyone point me to a sample configuration that shows how to consolidate analog and ISDN user remote access along with analog and ISDN dial backup on the same 3660 with 2 PRIs and two modem banks? This will be using AAA and tacacs+.
How can I clear the hits per access-list counters???
How can you Display the secret shared key in a router ???is it possible.regards per
Hi,We have a 3640 configured with Lock-and-key Security (Dynamic Access List) Installed IOS is:c3640-is40-mz_120-2a.binHere a extract of the config: aaa authentication login user tacacs+access-list 158 dynamic coxa permit ip any anyaccess-list 158 pe...
I am trying to implement a pix 515e in stages. I am able to put our exchange server behind the firewall and access it from outside, but I am having problems seeing it when on the same network as it. This is do to not being able to resolve the email s...
I am looking to increase the bandwidth of our firewall, a pix 520. I currently have a 100Mb interface and wondering what options there were as far as gigabit interfaces or adding some more 100MB interfaces to help carry the load. Thanks
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-30-2025 07:13 AM | ||
05-22-2025 03:30 PM | ||
05-03-2025 10:46 AM | ||
04-09-2025 12:34 PM | ||
04-09-2025 04:10 AM |