Does anyone know how to backup the IOS image of a 3005 concentrator? Before I upgrade the IOS to 4.7.2 I would like to make a copy just in case I have problems. Thanks for your help
Does anyone know how to backup the IOS image of a 3005 concentrator? Before I upgrade the IOS to 4.7.2 I would like to make a copy just in case I have problems. Thanks for your help
Hi, I have a hub and spoke network topology, and in order to access the spoke routers I use SSH version 2 from the hub router. Access is as follows: 1) I SSH onto a hub router from an UNIX server 2) Once logged into the hub router, I then SSH onto th...
I'm currently running Pix OS version 6.3(4) and considering upgrading to ver 7.X for Common Security-Level for Multiple Interfaces, Enabling/Disabling of ACL Entries and perhaps the virtual firewall features. Has anyone run into problems with these f...
global (outside) 1 interfacenat (inside) 1 10.0.0.0 255.255.255.0nat (dmz) 1 172.168.0.0 255.255.255.0
Hello everyone. I have CAS and CAM setup. I would like to use the virtual gateway mode in order to check user connecting through a vpn concentrator. My questions is this. On the CAS, the trusted and managed ip addresses must be on different subne...
I cannot launch SDM (installed on PC) with c2610 router (16m flash, 48M RAM and Advanced security IOS, the SDM shows me that the router is unsupported.I know that SDM should support old routers, so is it a problem of equipment or smthg else?Think you...
I have a software that can not connect to 127.0.0.1. I have read a few posts that say you can redirect ports using 127.0.0.2. I have tried that IP and it was not mapped. I have also looked to see if I can tell the redirect to be on 127.0.0.2, but c...
Hi,We are implementing a Two-tier firewall architecture using Fortigate and cisco ASA-5500 series firewall for our internal network.All the tiers will be redundant mode firewall (Active/Active)First tier firewall (Fortigate) will host the WEB servers...
I didn't use ASDM when I originally configured the firewall (PIX515E - 7.0.1) but I would like to start using it now. How do I go about adding the ASDM stuff to the existing config?Thanks!
I have taken over the admin duties after the term of the last admin and i need to recover access to the 3002's. The password will not work and I cannot get the hard reset to work, is there another way?
Has anyone got a solution for this.I have approximately 500 agents already deployed and with several waiting to be deployed.The reason they are waiting to be deployed is that they need AutoCAD LT to running. At the moment I cannot get AutoCAD LT & CS...
I have two sites connected to the Internet using ADSL and dynamic IP´s.Is there any way to configure a tunnel between the routers without using static IP´s?Perhaps mapping an ip host to a domain name (using a dynamic DNS and ddns updates on the route...
Hi, anybody tried this.?We have a DMVPN - Dual Hubs (7206) in our data centre. The Spoke sites normally have 1 * ADSL/SDSL ISP link and the 2 tunnels are configured to run down this one ISP circuit - one tunnel to each of the hub routers and all wor...
I have a very simple question regarding inbound/outbound connections.My PIX is a Cisco 525 running v6.3 software.We have a MS clustered server that provides 3 IP addresses.1. Virtual IP address for inbound TCP connections (FTP for example) to the cl...
recently I noticed a udp flood attack, which was originated by a LINUX server on a DMZ of my pix, where the server sent udp packets at very high rates towards the Internet through my pix. How can we prevent that?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-09-2025 12:34 PM | ||
04-09-2025 04:10 AM | ||
04-09-2025 04:03 AM | ||
03-27-2025 12:33 PM | ||
03-27-2025 10:07 AM |