I am running GSN3 on my laptop to create a test invironment, and after write erase, how long shoudl ir take to reload? Mine has been runnng for aobut an hour now.
Forum Posts
Hi, We are in the process of deploying nbar 2 throughout our organisation for better application visability. A lot of our internal applications are SSL and accessed via a browser, however. These applications have a wildcard certificate e.g. *.organ...
Hello, Just wondering if someone has experience upgrading to 5506H-X. I need to preserve the network, credentials and rule configuration from the1811. My plan is to transfer the configuration file via TFTP to the 5506. Is there any existing upgrade d...
Resolved! moduels and wic cards
Hi Team, Silly Question! I am wondering where to look to add modules to my cisco router 1841 and 2851 I only need to add Ethernet interfaces but I don't know how to look for them. :/ I know there are quite a few with Codes but thats where I get confu...
Hi All in Router i am the getting error:AMDP2_FE-6-EXCESSCOLL: Ethernet0/0 TDR=1, TRC=0Router is connected to Switch, both router and switch config is belowcan some body tell me how to fix up this issue as i am planning to change Duplex setting route...
I'm running eBGP with two ISPs on a single Cisco 4331. ISP A is a 100Mb connection, ISP B is a 20Mb connection. If I perform a "show ip route" about 60% of my outbound routes route thru ISP B - the smaller connection. How can I force more of my outbo...
Hi there!!! :) Basically I am wondering if I can do GLBP with Track between 2 interfaces on the same Router. Both interfaces are L3 on same Subnet. 1.1 and 1.2 So Can I use GLBP between thoese two and create a Virtual IP which will be Load Balance ...
Hello everyone, I have router configured in NAT, with 3 vlan's for certain purposes and DHCP server for each one.I show the configuration of the router, however and with regard to IPTV in Vlan 20, the STB only works for a few seconds and the image fr...
Hi I got below OID for ASR- CPU, but when i use through SNMP it show not recognize, I search and I found OID 1.3.6.1.4.1.9.9.109.1.1.1.1.24 it works, but the extension 2,3 and 4 when add not retrive any info. any one can help .1.3.6.1.4.1.9.9.109.1....
Resolved! CCIE Pre-Requisite
I have studies CCNA, CCNP, and CCIE (R&S) courses but not yet certified, if would like to go for CCIE Exam, is it necessary to be a CCNA & CCNP Certified? or i can attempt CCIE without CCNP certification? Please assist.
Hi Everyone, I am having Network devices in 10.90.X.X/24 network given by ISP. I want to access the server (10.60.x.x) behind the ASR 1000 series Router via SSH from the Host. ip nat inside tcp 10.60.X.X 22(Server IP & Port) 10.90.X.X(Router In...
Dear Team, We have 2 ASA , 2 DMZ switch , 2 serverfarm switch , 2 internet router and 2 6509 switch. Please help to design the network with best practice .
In my current setup I have an ISR4400 directly connected to the ISP. I am able to connect to the internet from the inside and ping any public IP as well as the outside interface IP.. However, I can not ping the outside interface from an outside IP. I...
Resolved! Cisco892/K9 DHCP Server don't work?
I Have interface Gi0 as nat outside and interface Fa8 with no ip address. I have created 3 subinterfaces on Fa8, listed below. How can I make such that each of them DHCP server working? int gi0 ip address 10.0.0.2 255.255.255.252 ip nat outside ......
I know that we can use 'bgp bestpath as-path multipath-relax' for multi-homed solution with same as-path length. Is there anyway to have multi-path for different path length. Such as: Network Next Hop Metric LocPrf Weigh...
