Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Labels

Forum Posts

Start a conversation

Ping between 2 SSID

Hi, I have 2 SSID on a router and would like them to ping to each other. So I would like to be able to have 2 devices connected one on each SSID and ping to them. How would I do this? thank you

Ed Lo by • Level 1
  • 1523 Views
  • 5 replies
  • 0 Helpful votes

Resolved! running crypto isakmp on cisco 2901

I have tried creating a vpn tunnel with my 2901 and can not get it to recognize the command crypto isakmp,  I have tried IOS c2900-universalk9-mz.SPA.154-3.M3 and c2900-universalk9_npe-mz.SPA.155-3.M6.bin.  i have also activated the security lic, i t...

broow by • Level 1
  • 1696 Views
  • 2 replies
  • 0 Helpful votes

Resolved! 2901 router needed for VPN tunnel

We had a Cisco 4331 fail and i need to get a site backup asap.  I have a 2901 router in stock i was hoping to setup to get the customer by until we replace the 4331.  What IOS do i need on the 2901 to have IPSEC capabilities to create a L2L tunnel?  ...

broow by • Level 1
  • 1058 Views
  • 3 replies
  • 0 Helpful votes

how sla monitor shift the line condition

hi, i have a problem with ASA sla monitor setting, i have 2 ISP (lets name it A and B) on the ASA. so i set a sla monitor to failover when the main ISP A line is down. thats means ISP A is active (main), the ISP B is standby. my configuration: sla mo...

ronald.su by • Level 1
  • 324 Views
  • 2 replies
  • 0 Helpful votes

Resolved! BGP routing policy

I have two sites, connected to client- A with 1G cable using ebgp. I am advertising 1.1.1.0/24 from both site to client-A. Site-1 has 1.1.1.1 and site-2 has 1.1.1.2 server. How can I choose shortest path to reach 1.1.1.1 or 1.1.1.2 ? (10.1.2.0/24 nat...

FORWARDING RANGE OF PORTS ON CISCO 871

Hello Guys i m new to Cisco and need some help to  forward the range of ports on Cisco 871 router to allow remote network phones to connect back to the PBX behind the Cisco 871 router.My ip for PBX itself is 10.10.10.250 and 10.10.10.251 is the DSP c...

kamal0005 by • Level 1
  • 2698 Views
  • 8 replies
  • 0 Helpful votes

Load balancing/sharing on WAN

Hello All,     I have this topology where I want to load balance between WAN1 and WAN2 ..     The switch Sw1 is a layer 2 switch not a layer 3 .. Is it possible to enable load balancing on the 2 WAN Connections from the routers directly or should I u...

Resolved! IP CEF Load Balancing

Hello Support Community Hope you are able to shed some light on my question. Below output showing CEF entry for the destination 10.255.225.26 and per-destination CEF load balancing algorithm is enabled. pe02#sh ip cef 10.255.225.26 detail  10.255....

mrana0101 by • Level 1
  • 4834 Views
  • 12 replies
  • 0 Helpful votes

Resolved! BGP announce a subnet that router doesn't have

HI all is there a way to announce a subnet segment that router doesn't have ?  for example ,  routerA have 10.1.1.0/24 on its Ge0/0/1 can routerA announce a /25 segment of 10.1.1.0 ?  i try it on quagga, it works , i want to know how to make it work...

missing pseudowire-class in 1801

Hi all,I'm trying to configure client-initiated l2tp on my 1801 box, but I don't have pseudowire-class on the general config help menu...Does anyone know why I don't have pseudowire-class in my global config? [Cisco 1801/IOS 12.4(15)T7][image c180x-b...

lajoe.aal by • Level 1
  • 3252 Views
  • 6 replies
  • 0 Helpful votes

Resolved! Cisco 892 Router no internet connection.

I am quite new to Cisco equipment but found this one cheap and got it and now struggling to set it up to work with internet. I am using cable internet modem which is connected to a cheap wifi router and assigning ip addresses to rest of the network. ...

Load more