Routing

Hey guys,Lets see if anyone can help me...I have one internet router connected to 2 different ISPs (SO 2 DIFFERENT ASs). Im using the bgp as path multipath relax, however, the AS-PATH length I receive from the ISPs are different, therefore, the route...

HelloI'm not sure about load-sharing by CEF, how it works. Hope somebody can explain it for me:For example I have two interfaces (f0/0 and f0/1) for equal-cost load-balancing. Now I set cef algorithm for layer4(config)# ip cef load-sharing algorith i...

Hi:I have a Cisco 2960 running 12.2(50) SE5 LAN base image. When trying to configure 802.1x in multi-auth host mode I am unable to get my clients to successfully connect.Under a normal circumstance (ie: no multi-auth host mode enable) 802.1x clients ...

Dear all,I'm working in a network of Catalyst 4948Es. I want to enforce the ospf cost of a port-channel interface, but at the same time I want the port-channel cost to change when any of the member links fails. If I use commands like 'bandwidth' or '...

HelloPlease can you assit, only the 4 lan lights comes on on my router and keep flashing. Non of the other lights come. Dose anyone what is happening?                   ThanksZakaria

Hi everyone,I have an ISP that based on ADSL media.I have a ASR 1002 router and a 3560 SW and some Servers.I have a range of IP address /24 but I will take 1024 IP from RIN and want to run BGP between my internet service provider.Now I have 100 onlin...

We have an MPLS WAN with 2 DS3 routers.  The routers are not connected to each other.  I want to load balance the traffic across the DS3's.  Right now traffic is just taking the best path according to BGP.  Will I need to run GLBP on the front side (...

I am at a site and have an interesting HSRP situation between two 7200 routers. These routers are running v15.0(1)M3 (AdvSecurity) IOS and configured interfaces are both G0/2 on each router.They are laid out as shown in the attached drawing, nothing ...

Hi all,I've been trying to get this to work , but it appears to be a bug of some sort . I have two VRFs configured on a physicall 1811 running (C181X-ADVIPSERVICESK9-M), Version 15.1(4)M6one is called inside facing the LAN and one is called outside f...

Hi,We have 2 router ( A & B) connected with different ISP ( C & D) via EBGP with different Public AS no provided by ISPIn between 2 router( A & B) we are running IBGP so that any ISP link fail, traffic can take IBGP path to internet via alternate ISP...

                   I have a lab setup for eigrp R1 has 5 equal links to reach R7 , with same bandwidth, On what cretirea it will select best 4 next hops to reach R7.

Dear support Team,How can I Setup Two Router for redundancy for the following solution•1.       Setup up two routers with three(3) connections: A,B,& C ( RJ 45 Cat6 cable) to each other•2.       The three connections are complimentary to each other•3...

Hi. We have this configuration to orderCISCO3945/K9S39UK9-15204MSL-39-DATA-K93900-ZTD-CFGC3900ISR-CICS-SLNM-1A-OC3-POMSFP-OC3-IR1SM-NM-ADPTRPWR-3900-ACPWR-3900-AC/2CAB-ACEC3900-SPE150/K9PI-MSE-PRMO-INSRTSL-39-IPB-K93900-FANASSYISR-CCP-EXPMEM-3900-1GB...