Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...
Hi,I'm using a router WAN Cisco ASR1001 connected through BGP AS65075 with our ISP.This router is connected through OSPF with our firewall Cisco 7206VXR/NPE-G2.Topology :ISP <- BGP -> RT 1001 <- OSPF -> FW 7206 <-> LANOn the WAN router, static routes...
I am running a number of ASR1001s running 15.1(1)S. I have QoS setup but see drops in some of the queues from time to time. I know we have the bandwidth to accommodate the traffic. There has to be a way to allow the queues to go beyond their bandw...
Hello Guys,I'm having problems with SNMP in a couple of Nexus 5000 Series. Practically it stops responding to snmpwalk and in timing out.If i issue command no snmp-server protocol enable, snmpwalk returns unreachable, but if it is enable, no unreacha...
Does the 2821 router support jumbo frames on the integrated gig ethernet ports? I need to up the MTU size for MPLS. If it does, what is the command to do that? I can't seem to find any commands that relate to MTU size in the 2821 I have. It is run...
Dear Experts,We are running 3 ISPs bandwidth via eBGP in our router with our own ASN and IP address.Now our one of the client has their own IP address and ASN from APNIC .So now what configuration required in my router as PE for our client ASN and I...
We have QOS over our MPLS and my provider says that our QOS policies are working fine, but when I run the show policy-map interface command it always shows the EF que with 0 packets and using up 25% of our bandwidth. We are not ta...
hi..will QoS support on interfaces configured with IRB....?pls explain..?
Hi,Apologies for my first post being a question but I've got an urgent problem to solve before Monday morning. I'll try to keep it as simple as possible without missing out any important information.We have moved our servers, routers, firewalls etc t...
Good day.Few week ago we purchase Cisco ASA 5505 as replacement broken Dlink DFL800.I try to configure all setting like it was on DLink, and all work fine with exception of one thing.We have some resource like terminal server, that placed in internal...
Hi all,i have some problem regarding BGP table convergence. There are two router (ASR1K and CRS-3) which have a direct interface and peering with loopback0 adresses.The BGP Peering is established, and prefixes are transfered. However, from ASR1K to C...
Hi Alls,I have some concerns, if we consider QoS, we can configure QoS as following for instance.policy-map **name** class **name_A** set dscp default class **name** set dscp af20 class **name_B** queue-limit 8192 service-policy **name_c**...
Hi,I came across an error that seems simple but I cant solve the issue. I could'nt pull the startup config from an AP via Cisco works so I connected to it and tryed to do a show startup-configuration. But when I did this, the following error occurred...
HiI have this Ethernet/Token Ring Router and would like to know howto put the interface TokenRing0/0 up?ETHTR#sh versionCisco Internetwork Operating System SoftwareIOS (tm) C2600 Software (C2600-I-M), Version 12.2(5d), RELEASE SOFTWARE (fc1)Copyright...
We have a 3600X ME acting CPE with per vrf BGP towards a PE router.Pxe boot for clients on vlan interfaces in the vrf's does not work, while DHCP relay works just fine.We have both the DHCP server and the PXE servers addresses defined as ip-elper add...
Please provide me why my router rebooted?reason is: bus error at PC 0x23B1F92C, address 0x3CWhat does this mean&show ver:Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.2(3)T, RELEASE SOFTWARE (fc1)Technical Support: http://www.c...
.png "Hall of Fame"){kind=icon}
