Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

Can someone confirm or deny that Cisco does not currently support Key-Chains for BGP in IOS?I know BGP peers can utilize MD5 MANUAL passwords but cannot find anything on Key-Chains for BGP in IOS. (not looking for Cisco XR boxes).TksFrank

fsebera by Level 4
  • 3856 Views
  • 9 replies
  • 5 Helpful votes

Hi all,This is the first time I've ordered a Cisco router before, to replace my Draytek basically. Well, this morning my 887VA-SEC-K9 router arrived, followed some of the help guides I managed to find eventually that said things like grounding, cable...

ubyu.net by Level 1
  • 599 Views
  • 2 replies
  • 0 Helpful votes

Hi,With the same 877 modem plugged in the same line.  PVC configured with VC/MUX and PPPoA.  We chose the PPPoA because we have 1500 Bytes MTU. (The PPPoE have a 1500-2-6=1492 MTU).  IOS: Version 12.4(15)T10, RELEASEIf we put an "overload nat" we hav...

osgpcqosg by Level 1
  • 3526 Views
  • 14 replies
  • 0 Helpful votes

Hi Expertsmy CORE Switch 4507R Suddenly restarted (Powe is good) , and gets the business down for 30 Mts,my boss came to me and asks why it has restarted , what is the root cause of this restart pls send me a report, i dont have any syslog or NMS ena...

Hello all,How can I work with EIGRP in the company routers, if in the middle of the links I have the ISP routers and I don't want them to participate in the EIGRP process?

Dosorio31 by Level 1
  • 1879 Views
  • 7 replies
  • 0 Helpful votes

I have noticed some odd NAT entries, and cannot explain them.  The static translation is:ip nat inside source static 192.168.0.222 111.111.111.111There is an inbound ACL on the WAN interface that only allows a few standard ports.  Yet I see translati...

thomas947 by Level 1
  • 535 Views
  • 1 replies
  • 0 Helpful votes

hi I have configure :my local routerrouter bgp xxxxxnetwork 10.1.1.0 ....neighbor 10.2.2.2  remote-as xxxxxneighbor 10.2.2.2 next-hop-selfand my border router has bog neighbor to them with local-preference 30 to external link. so I have get default r...

julxu by Level 1
  • 841 Views
  • 4 replies
  • 0 Helpful votes

For some reason my ASA is preventing my traffic from going out. I've added some crumby access-list and applied it to NAT for it to work. I don't like this. I know it is not right, but I am not sure what part is wrong. I will highlight the stuff I hav...

I have an 1841  with a Wic/Hwic 0 DSU/CSU installed and working well.  However we added another Wic/Hwic 1 DSU/CSU into slot 1 and the 1841 is not seeing it.  If I do a show inventory it does not show.  Can I have two DSU/CSU in a 1800 series router?

Needing to bridge from my wic interface to an ethernet interface on a 2900 series router so that I can pass through the ip address given to the WIC, to my ASA so that I don't have to give my ASA a private range address. (Just like a service provider ...

lcnorwood by Level 1
  • 687 Views
  • 1 replies
  • 0 Helpful votes

Thanks in advance for your help, I'm hoping that this is a known issue since it occurs on several of our 4500 access swiches with redundant sup V and port channel uplinks (routed) to 6500 (core) switches, two to three times a day we experience the lo...