This is a Hub and spoke scenario of mpls connectivity using bgp. Also the dc and Dr connected through an additional replication link(ospf). So I want a solution that, if the isp1 connection of dc down, branch can able to communicate dc servers throug...
Hello Guys,I'm having this problem with a Cisco device:The interface Interface Vlan3 "dmz", is up, line protocol is up Hardware is EtherSVI, BW 100 Mbps, DLY 100 usec MAC address 0007.7da7.54d6, MTU 1500 IP address 10.40.18.8, subnet m...
Hello, My current router is running IOS version 17.06.01. I placed the new IOS 17.06.03 in Dir and changed the boot sequence to boot from .03. But any time it boots is start from .01 any suggestion to have the router use the upgraded version. I alrea...
I'm having an issue with routing I can't seem to figure out. We have a Cisco 3850 switch stack that operates at the gateway for all devices on our network. The 3850 then routes traffic to our firewall (10.51.5.1) before going out to the internet. We'...
I'm looking to add a MED to BGP of a secondary router in one site, but I'm having problems with it. Router(config-router)#route-map MED permit 10 Router(config-router-map)#set weight 100 Router(config)#router bgp 65000 Router(config-router)#neigh...
Hello professionals,Doing some testing regarding static routes and whether to use the next hop IP address or the outgoing interface as the next hop. My question is: Can I use the outgoing interface as the next hop when configuring a static route to r...
Hi,Am looking at purchasing a router that is capable of serving a WAN bearer at up to 1Gbps. The 3945E has had good reviews as a high throughput router but the datasheets suggests performance of 350Mbps. It also states that additional performance c...
Hi,Can anyone share a configuration file of ISR C1121-8PLTEP workable config? Just need a VLAN on Gi0/1/1 and Gi0/1/3. Then DHCP pool on that vlan. To achieve if a terminal device(PC) connect to Gi0/1/1 or Gi0/1/3, it can get a DHCP ip address. I tri...
I am getting ready to lab this up, but I do not understand how this works (but is). Thought I'd seek some opinions first.I have a router (a bunch of them) that has a static default route to an IP in a subnet that it is not connected (8 hops away). Th...
hello. We're looking to implement interface (IP event) and BFD dampening. We currently have BFD being tracked by BGP as well as BGP route dampening in place :interface te1/1/1bfd interval 700 min_rx 700 multiplier 3 router bgp 65000bgp dampeningneig...
I do not know if it is the group of acuado however download here to see if they can give me a hand.We have a router C3900-SPE200/K9 to rout the calls to CUMC, for a few days we are observing that the e1 are in UP state but the lllamadas does not ente...
I'm embarrassed to ask this, but I need to confirm...1. What is the difference between configuring a workstation endpoint with a /24 or /32 subnet mask?2. Does workstation endpoint 10.0.0.77/32 on network 10.0.0.0/24 receive its /24 network broadcast...
Hi Team,i am using Cisco IOS XR Software, Version 7.2.2 as PCE controller and trying to put md5 clear password but XRVR is not accepting password length more than 25 character.Any known limitation for this ?config denying more than 25 character and a...
I have following configuration. My tunnel is up but i cant send routes since yesterday. I have done nothing to the original configuration. My router is not advertising my routes interface Tunnel1ip address 100.200.10.5 255.255.255.0no ip redirectsip ...
So i have 1841 set 0/0 has fios internet. 0/1 has 4 sub vlans set. Ping via serial on both. ping to 0/1 network on all subnets. cannot get orbi set on vlan a - so cannot test internet ping. Any help would be appreciated. Plan is to introduce a s...
