Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...
Hi,We're configuring up a Cisco ISR4331. Cisco IOS XE Software, Version 16.09.05 Cisco IOS Software [Fuji], ISR Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 16.9.5, RELEASE SOFTWARE (fc1)It connects to the internet via an ISP provided PPP conn...
Err... For some reason, my previous question... got kicked or something? I have no idea, but it seems not to be publicly visible anymore, and I can't see any replies. So, I'm gonna try asking again? I can't imagine what I might've done wrong; it's a ...
Hi, I just configure SSH v2 on my Cisco 4331 router. and I change my default SSH port. It is working successfully under LAN network. But I can't access the Router using WAN IP from a remote location. What may be the Problem?
Hi All, I'm a little confused on the IP SLA..I've read the Cisco Documentation, websites, but I still can't grasp the understanding of it.Can someone help me understand it in plainly please? I'm using the following syntax, but when I setup the frequ...
hi,i got a 4321 router that i activated for temporary/eval license. we upgraded it to 16.12.4 and saw smart license started 16.9.xi would need the 'throughput' and CME/uck9 permanent license installed. but the vendor gave us the traditional PAK/PDF f...
Greetings, I have an issue moving from EHWIC-4G-LTE-V on a 2921 to a NIM-LTEA-EA on a 4331/k9. Basically, once I move it over the modem prefers Band 4 over Band 13, (which the EHWIC preferred), and my signals are much worse, (To the point our NOC ...
Hi A DHCP windows server is connected to switch. This switch and other switches can ping the server. I want to confirm dhcp ports are good open. Do you think I can confirm this issue by telnet it? Thank you
Hello, I'm a neewbie on the IOS platform after years on the ASA, FTD platforms I am using a Cisco 829IR to deploy IKEv2 between HQ and a remote location. The unit is connecting with IKEv2 againts HQ with Cisco FTD units. This traffic is flowing as ex...
Dear All, We're implementing DMVPN with Dual Hub and approaching Dual Cloud for bank network with hundreds of branches , please advice on the best practice to implement DMVPN with Dual Hub Dual/Single Cloud with higher redundancy and failover. regard...
In what situation would you use which Routing Protocols? EIGRP, OSPF, IS-IS, BGP, RIPv2? I'm trying to gather a better understanding what situations call for them. Thank you everyone for your help.
Hello everyone, im planning to config a LACP between XR Router and QFX switch. My questions1- is my LACP connection is correct or the MUX state must be ATTACHED not DISTRIBUTING ? 2- how i can config ip address ( Gateway ) for the aggregated Inte...
The MPLS QoS E-LSP solution must use additional signaling to establish the LSP neighbourship. Is this statement is true?
When MPLS TE Hot Standby is deployed if BFD for TE CR-LSP is used to check faults, the round trip paths of BFD packets must be consistent to prevent wrong TE LSP switchover. Is this statement true or false?
An LSP can be established by manually establishing hops or by the label distribution protocols. Is this a right statement
Multicast VPN supports inter-domain VPN Option A, B and C. Is this right statement?
| User | Count |
|---|---|
| 16 | |
| 13 | |
| 8 | |
| 6 | |
| 6 |
.jpg "VIP Mentor"){kind=icon}
.jpg "Hall of Fame Master"){kind=icon}
