I've been dedicating some time to multicast, I would like to know howver how often have you come across doing multicast routing as a network engineer?
I've been dedicating some time to multicast, I would like to know howver how often have you come across doing multicast routing as a network engineer?
Hi, Can anyone confirm if i add a DHCP help address to a switch with a layer 3 interface in the same vlan (that is not the default gateway) would the switch pass on the DHCP discover request from the workstation? or does it have to be added to the ro...
Hello I have found below comment online about ospf passive interfaces on IOS XR. Command Defaultios xr, ospf, passiveIf this command is not specified in interface configuration mode, then the interface adopts the passive parameter specified by the ar...
I have a setup where we maintain our own MPLS core with multiple VRFs. We are moving to a next phase where we want to do inter-vrf routing. At a high level, if I have the following: VRF A - path to internet, (default route is available), path to to...
Are there any troubleshooting commands that can be performed to rule out a transceiver issue? In the past I typically start at one end of the link and start replacing sfp's and fiber optic patch cords until the CRC errors stop incrementing.
can anyone point me in the direction of a SIMPLE VLC multicast lab? I don't even mind if it's 1 or 2 routers, a VM and loopback I just want to be able to stream from one end to the next and test out commands afterwards
Hello, I have the following messages in my debug ip nat : *Nov 16 14:22:21.711: NAT: s=10.39.226.100->10.233.1.3, d=10.233.90.100 [11047] *Nov 16 14:22:22.075: NAT*: s=10.39.226.100->10.233.1.3, d=10.233.90.100 [11048] Everything works fine but I...
Hi all, I have OSPF set up between 3 routers and R2 keeps going with: state Speak -> Standbystate Standby -> Activestate Active -> Speak over and over. Neither R1 or R3 has this issue. Here is the topology: And here is the ospf section from "show...
Hello all. We have followed the process for Password recovery, but all the box does is boot back in to rommon mode, nothing else. Also, if No password recovery was entered in to original config, how can we restore if this was the case? Thanks i...
1. Configure R13 as PPPoE Server 2. Configure R14 as a PPPoE client 3. The link must be up even if there is no traffic 4. R14 must always receive the ip address 131.131.34.4/32 from R13 5. Do not use DHCP to assign the ip address 6. Avoid unneeessary...
Hi, I'm studying for my CCIE and exercising with EIGRP. All my exercises are done in CML2, using IOS Version 15.9(3)M3. In my last LAB I was playing around with different paths and how adjusting the metric changes the FD, CD and RD. The Route...
Hi Guys/Gals, I am having trouble understanding the use of ACL' s in SNMP groups and can't seem to find the exact answer. The thing is we use SNMP groups for custom views and we would like to limit access to trusted sources via an ACL. Howeve...
CSC Can you explain why i have dual CSC profiles and as such dual posts
Hi all, I have a question regarding ASR1001. we have used the current 2x10G ports and planning to upgrade other ports to 10G port too.i have read datasheet ASR1001 and is it possible SPA slot to support ASR1000-ESP20? i just want to confirm that only...
Hi Folks Wonder if you could help have an ISR 4331 with an SFP (SFP-GB-GE-T) in interface G0/0/2. It is set for auto negotiation and negotiates to 100M/Full duplex to an ADVA NTE. Although the interface comes up I am seeing CRC errors. The circuit th...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-18-2024 07:58 AM | ||
10-17-2024 11:42 AM | ||
10-16-2024 07:21 AM | ||
10-16-2024 12:58 AM | ||
10-15-2024 08:44 AM |
User | Count |
---|---|
11 | |
9 | |
7 | |
7 | |
6 |