Routing

Hi all,There are three diagram, Does the routing table of bottom routing is correct ?

I am trying to get a 7507 and a 3550 to talk via ospf. The first router is 10.91.0.1 and the switch on vlan 1 is 10.91.0.100. The 3550 will learn all the routes and install them but the 7500 will see any routes from the 3550. The sessions are up:7...

See attached picture...I'd like to leverage a peer router to direct some VPN traffic. Can anyone tell me if this approach is possible or if there is a better way?China Office:int 0/0 IP: 4.4.4.1/32int 0/1 IP: 5.5.5.1/32 (second ISP)US Office:Public ...

Our network is part of Verizon ATM Cloud - we have two remotes sites that work great they do not drop pings(1000 bytes) They each run on 1.5 ATM. At the Main site we have a DS3 10mb. that the two remotes come into. We also have going out 6mb PVC to o...

Hi, I have connected VMware ESX server to Cisco 6509E Switch. I have created 3 VLAN in the switch. I have to apply ACL in VLAN interface. Any idea which Port & Protocol (TCP/UDP/IP) need to open in ACL for the VM communication. I have to apply Deny a...

Hi,Our provider cannot provide us an ethernet access connection for one of our existing site. He propose us to start with 2 x E1 in MLPPP.I would like to know if there are some limitation using MLPPP?Also, we have a CISCO2801 in that site, and plan t...

Newlly deployed a 2811 router with two E1s MLPPP bunddle new brach office, at first all seem fine connected to MPLS provider. Then hours later users began complaining, looking at the E1 noticed lots of line code violations and one of the E1 keeps dro...

Presently I am using the below IOS in my 7600 router c7600rsp72043-advipservicesk9-mz.122-33.SRC1.binIn qos configuration i am getting the following error -------------------------------------------------class-map match-all ILL match access-group n...

I have 1:1 Internet link. I need to connect to VWIC2-2MFT-G703 card and how to configure the VWIC2-2MFT-G703 card in 2821 Router? I have public ip address, whether its possible to configure in VWIC2-2MFT-G703 card? please help me to solve this issue.

i have one router with two ISP connections (one tiered ds3 (isp1) and one multilink (isp2)) - we want to test the new ds3 before we put it into production by routing the tech department (10.10.1.x) Internet traffic out of it - then have the remote br...

Hi all,I'm looking for some info from people who have deployed these types of cards. We have need for a wireless backup on a 2801 router that terminates a T1, but does not have Cable or DSL in the area. We tested a satellite link, but the latency is ...

Hi,Does anyone knows how to run GRE Tunnel over IPSec. The scenario is bit different. Let me try to explain. PE1 and PE2 belongs to ProviderA which is basically public Internet. PE3 and PE4 belongs to ProviderB which runs IPVPN private network. CPE(...

Hi,I am working on running OSPF over PPPoE, It works fine with DHCP pool with /24 subnet but with negotiation as client is getting /32 ip address its not working because client and server are at different subnets... so what to do to get it resolve?re...

Hi,I have a Unframed E1 on Cisco 1841 with VWIC-1MFT-G703 card. Can WIC 1T card be used to replace the VWIC-MFT-G703 card ? WIC1T supports Unframed E1 or not..?Thx,Gaurav