We are trying to determine the End of Vulnerability/Security Support:HW for a Cisco ISR4451-X.Following the eol documentation on the following link, it states February 8, 2022, is this correct: - https://www.cisco.com/c/en/us/products/collateral/rout...
Forum Posts
R2: R2 can ping R4 as it is direct connected R2#ping 24.0.0.4Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 24.0.0.4, timeout is 2 seconds:!!!!! R1 cannot Pinfg R4ype escape sequence to abort.Sending 5, 100-byte ICMP...
Would like to ask on how to know on what is the use or purpose of 200GB SSD in ISR4451-X/K9 router. What show commands are we going to perform in order to check the SSD capacity/free space/used in our router? Thanks cisco ISR4451-X/K9 (2RU) processo...
Hi Everyone, As part of my homelab I purchased a number of older Cisco Routers and Switches. I've managed to learn a great deal about getting these setup and running. Now that I've finally been moved across to FTTP I want to replace my consumer route...
Hi i still wondering what happen in my cisco router,my command automatically deleted by router, i'm not doing anything not even reload the router.Please help.the command is ip nat source ip addr1 ip addr2 extendable. Thank you
Resolved! BGP Incorrect netowrk or mask
trying to get loopback addresses to advertise *Mar 1 00:44:04.715: %SYS-5-CONFIG_I: Configured from console by consoleR2#conf tEnter configuration commands, one per line. End with CNTL/Z.R2(config)#router bgp 500R2(config-router)#network 192.16...
Resolved! Cannot Update Source Loopback For BGP
Trying to switch my source from R12's F0/0 interface to its L0 interface interface FastEthernet0/0ip address 10.1.3.12 255.255.255.0duplex autospeed autointerface Loopback0ip address 12.1.1.1 255.255.255.224exitrouter bgp 1000bgp log-neighbor-...
Resolved! Wildcard misunderstanding
Hello I have done best I can in terms of research on what Wildcards are but I just am not processing it.Do Wildcards work to create a range? For example, would 192.168.1.0 0.0.0.15 mean 192.168.1.1 - 192.168.1.15? I want to break up 1 Network onto 2 ...
Resolved! OSPF priority vs cost
i have two data center. sharing data with each other via isp ckt. Port channel coming from router has configure priority as well as ospf cost. I want to know what's the difference between priority and cost. Also, can we just use cost to make routing ...
Hello, Cisco community I am looking to configure Cisco 4321 router with Call Manager and pass the SIP traffic to Cisco IP phones. Has anyone done the configuration before? Any help would be much appreciated.
Hello I was wondering if it would be advisable to manually input my WAN default route as well as it being obtained. I ask because when it is obtained manually via PPPoE it does not show up in "static routes". Curious if I should also manually make ...
Hello -Looking for input on 4331 max IPsec throughput when boost & HSEC license installed We have a case where two locations (both with 4331's) are having internet WAN links updated to 1Gb. The only way to attempt to get the full throughput (general ...
Resolved! Copy HTTP VRFaware
Dear community i would like to use a command like this: copy http://ciscoiosimages.company.local/image123.bin flash:image123.bin vrf LAN I know there are things like: ip ftp source-interface Loopback0 ip tftp source-interface Loopback0 But there isnt...
I migrated configuration from ISR1921 to ISR4221, but find ip load-sharing per-packet command(used in ISR1921) is disable in ISR4221(CEF is enable), only ip load-sharing per-destination is enable by default.know load-sharing per-packet command is not...
Resolved! Bin files for Cisco 7940/7945 phones
Hey team, so I’m pretty new and I just built a home lab, 2x 2811, 2x 2960, 2x 3560, 2x 1841, and an ASA 5505. The issue on having is the Voip phones fully configuring. The phones will boot and it will pull the right default gateway and it will show...
