Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Hi,We are using ASA Version 7.2(2) Firewall and its configured public IP 122.166.9.59 for external interface. The customer using one remote desktop in side network for accessing from outside .Can we use single public IP for firewall external network ...

Dear All,May I know under what kind of situation the CTS will show down, the circuit is running fine currently. thank you.SATTSA1#sh int s1/0Serial1/0 is up, line protocol is up Hardware is M4T MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, re...

trinawong by Level 1
  • 1169 Views
  • 1 replies
  • 0 Helpful votes

Hi all,I am having a query regarding FDDI token ring. I am looking for a switch which can support FDDI Token Ring. The following documentation leads that Cat 5000 and Cat 3900 supports FDDI Token Ring. But those switches are End Of Sale. http://www...

jachowda by Level 1
  • 509 Views
  • 1 replies
  • 0 Helpful votes

I am trying to setup an acess server to allow reverse telnets into a practice lab. I was able to get this working but I would like to be able to establish the reverse telnet sessions without entering a username and password. The access server is pr...

izackvail by Level 1
  • 500 Views
  • 2 replies
  • 0 Helpful votes

No sure if this is the correct forum but we are prepping a network for Voice and making sure all QOS requriements are set correctly setup.We have a network of CAT65K with SUP720. We will be enabling MLS QOS on the switch which will set all ports to u...

paulhardy by Level 1
  • 545 Views
  • 4 replies
  • 0 Helpful votes

I have a customer with the standard AC power supply in a 2811. Can I simply order the spare PWR-2811-AC-IP= so that I can get PoE in the chassis and swap the power supplies? I want to make sure that I have all of the system board connections and cabl...

kbyrd by Level 2
  • 1857 Views
  • 2 replies
  • 0 Helpful votes

Resolved! Block O E2 routes

i have 3 routers in ospf area 0.SW1-interface Vlan1 ip address 9.9.9.1 255.255.255.248 ip ospf network non-broadcast ip ospf dead-interval minimal hello-multiplier 10!router ospf 1 log-adjacency-changes network 9.9.9.0 0.0.0.7 area 0 neighbor 9.9.9.2...

rmv72 by Level 1
  • 1097 Views
  • 3 replies
  • 0 Helpful votes

I am preparing for ISCW exam.I have 3 2610XM routers, I am trying to do MPLS lab in this router with latest enterprises IOS image, unfortunately there is no MPLS in this IOS image.If any body know which IOS is compatable for MPLS in cisco 2610XM rout...

Hi we have an 876 which connects to our main sites via IPSEC. I want to limit the bandwidth between hosts 10.100.8.201 too 10.100.3.220 at our mainsite. The traffic between the two flows via an IPSEC tunnel 10.100.8.0/24 -> 10.100.3.0/24 I only ha...

One of our customer needs to go for a second ISP for redundancy and load balancing. They r using VSNL IP inside for webserver. Their second ISP is Reliance. They need to use the same IP address when they need to route the packet through Reliance in c...

Router where i try to redistribute from BGP into OSPF -interface Loopback0 ip address 172.22.21.104 255.255.255.255! interface GigabitEthernet0/0 description ### Int to AS65337 ### ip address 9.9.9.2 255.255.255.248 ip ospf network non-broadc...

rmv72 by Level 1
  • 1049 Views
  • 4 replies
  • 0 Helpful votes

Hello !I have a Catalyst 2940-8TF switch with MTRJ optical port and I cannot get the optical link up. It wouldn't establish a link with multi-mode optical bridge converter, and it also wouldn't go up if i connect its own tx to its own rx. I have trie...

ivu by Level 1
  • 458 Views
  • 3 replies
  • 0 Helpful votes

Please advice!!!Remote 1800 router has L2L VPN back to headquarter. The bandwidth in 1800 router is 1.5 MB. However, sometime the traffic may reach the limitation of bandwidth, and the application will be dropped.Here are the followings we did:1. Che...

kzhen by Level 1
  • 607 Views
  • 4 replies
  • 0 Helpful votes