Resolved! Cisco Telepresence
Can a Cisco Catalyst 6506 Switch support Telepresence?Appreciate your responseRegardsNavneet
Can a Cisco Catalyst 6506 Switch support Telepresence?Appreciate your responseRegardsNavneet
Hi,For the redistribution route into ospf. There are two type we can use.One is metric-type 1, the other is metric-type 2. How can I choose it.1. Under what condition use metric-type 1 or type 2?2. Is it metric-type 1 is more prefer to use as it calc...
Hello all, More of just a general functionality question on a UBR7246. How well does Downstream load sharing work? We have several locations that are running out of downstream bandwidth and would like to just send a second downstream channel to ...
Hi,I'm getting confused with the kinds of OSPF network in Frame-relay. Well I know of course what is a point-to-point link but I want to know the difference between these:RFC-Compliant:Non-Broadcast MultiaccessPoint-to-MultipointModes from Cisco:Poin...
Hello All, May i kindly seek an urgent assistance to curb the perpetual disruption of my Access server which hangs from time to time with the following outputs?.Access-Server#..r2Trying R2 (192.168.1.253, 2002)... Open[timed out]Loading cisconet.cfg...
Hello,I have a little problem. I configured an ADSL 877W. After it was plugged in, the dialer interface negotiated its IP address ok, but after a few minutes, the atm interface started flapping. It flapped a couple of times, then i lost the IP addres...
as a practice I'm trying to setup qos on my home router but so far it hasn't workedheres what I've tried so far------------------------------class-map match-all Xbox360match ip dscp 8policy-map Xbox360class Xbox360priority 208 310interface fastethern...
Dear allI want to calculate MTBF for my campusis there any software for this issue or does any one know how to calculate MTBF?regards
I have an asymmetrical 8 Mbps/1 Mbps international cct between with Cisco 3845 routers on either end.The latency is typically 800mS. The maximum TFTP transfer speed we can get accross the link (in either direction) is around 55KB and therefore not ut...
I have a 7206 router I am replacing with a newer 7206 that connects all remote branches.My existing 7206 is using BGP to connect remote sites and distributing BGP into OSPF.I have the second router up and running connected to the network by a single ...
Hi, I try to redistribute static route 188.188.188.0/24 from Router 16A and 16B with metric-type 2. I think 16C will have 2 equal cost route install in the routing tableE2 188.188.188.0 [110/20] 192.168.1.1E2 188.188.188.0 [110/20] 172.20.1.9However,...
Hi I have a setup where I need to track the reachability of customer end router from my datacenter router. I have two redundant paths to reach the customer router and we are using static routing. End to end ping reachability is also successful throug...
Hello,I noticed the following logs in a test environment at a cisco academy:MAC#sh log | i Feb 4Feb 4 12:04:34.858 UTC: %BGP-5-ADJCHANGE: neighbor 192.168.10.1 Down BGP Notification sentFeb 4 12:04:34.858 UTC: %BGP-3-NOTIFICATION: sent to neighbor 19...
Dear all,Please explain what is meant by suboptimal paths..thanks,dreams
Hi,Just a quick question about policy-based routing. For example, packets that came from 10.0.0.0/8 going to 20.0.0.0/8 should be routed to next-hop 1.0.0.1. I used the command set ip default next-hop 1.0.0.1. If the routing table has an entry for 20...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 12-04-2025 12:04 PM | ||
| 12-04-2025 08:01 AM | ||
| 12-03-2025 07:46 AM | ||
| 11-13-2025 04:57 PM | ||
| 11-09-2025 09:51 PM |
| User | Count |
|---|---|
| 10 | |
| 6 | |
| 5 | |
| 4 | |
| 4 |