Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

Hello Community !I recently acquiered a cisco 898EA router and i have been struggling to configure it properly.My first goal is to connect the WAN port (Gi8) to a 192.168.3.0 network with the gateway at 192.168.3.254 and to connect a LAN port (Gi0 fo...

fenoyr by Level 1
  • 610 Views
  • 4 replies
  • 0 Helpful votes

Anyone know how to configure vxlan from cisco nexus to catalyst 9500? I need expand some vlan on nexus to c9500 in different location using tunnel interface so both location will share same vlan.

hs08 by VIP
  • 373 Views
  • 3 replies
  • 0 Helpful votes

Currently i have 2 nexus devices and runnging hsrp for redundancy. Both nexus connected to the firewall. Then i need to migrate the server to new location without downtime. In new location i have c9500 as core and also firewall. My plan to make tunne...

hs08 by VIP
  • 255 Views
  • 1 replies
  • 0 Helpful votes

Hello,I have very simple Cisco EVPN VxLAN fabric running on Cisco nexus 93180YC-EX switches. I am using OSFP + iBGP for underlay/overlay with Multicast. I have border-leaf switches connected to single ISP with eBGP peers and I am advertising my publi...

What's wrong with this config? It works when I don't put the vlan/server in a VRF. 3850 is the DHCP server: vrf definition VCCrd 100:1!address-family ipv4exit-address-family ip dhcp excluded-address 10.1.11.2 10.1.11.99ip dhcp pool vlan11vrf VCCnetwo...

I have one general BGP question and like to know how this problem is addressedMy topology has 4 BGP speakers, each in different AS number. Mesh topology between this routers:Each router has eBGP session with other routersR1-----------------R4|       ...

I have created an ACL rule in WLC where the goal is:ip source: 10.20.116.0 / 255.255.255.0dest: 10.0.0.0 / 255.0.0.0 (deny)as I show like this.the current result is,dest to 10.20.111.240 (example) deny/rejectbut the problem is that access to the inte...

Riimeister_0-1739349183314.png
Riimeister by Level 1
  • 1734 Views
  • 15 replies
  • 0 Helpful votes

I ran into an odd issue I have never seen before...I've got a 2901 router in a remote office that terminates a PRI into our call manager.Got a call from the site saying they couldn't call out... I tried to call in and couldn't either.I tried to telne...

aBs0lut30 by Level 1
  • 1502 Views
  • 6 replies
  • 0 Helpful votes

I created a loopback address and assigned it an ip address, I cannot ping my tftp server from the router nor can i ping the loopback address from the pc.Router4331#copy flash: tftpSource filename []? pp-adv-isr4000-1612.1a-37-49.0.0.packAddress or na...

moman62 by Level 1
  • 568 Views
  • 8 replies
  • 0 Helpful votes

Resolved! 4331 router

I am trying to tftp to my pc the old ios's on this router and am getting this message when doing so.Router4331#copy flash: tftpSource filename []? /bootflash/isr4300-universalk9.16.06.07.SPA.binAddress or name of remote host []? 192.168.0.10Destinati...

moman62 by Level 1
  • 692 Views
  • 7 replies
  • 0 Helpful votes

Dear Team,Greetings,I have a request from a team located in another country (vendor) to access my SQL Database. They will provide us with the IP address that needs to be whitelisted, which will be added to our ASA 5512-X firewall for communication th...

manojyesh by Level 1
  • 936 Views
  • 14 replies
  • 0 Helpful votes

I set up a C1121-4P router for a friend with int gig0/0/0 facing the ISP with ip address dhcp. int gig0/0/1 192.168.1.1/24. See attached sh run. Vanilla Configuration not much security or complexity. After a power reload the GUI "https://192.168.1.1/...