I am planning to buy NTP server which is supporting version 2,3,4. is it possible to sync the time of switches and routers with this server. Need suggestion on this.Rgds,Sarbudeen
I am planning to buy NTP server which is supporting version 2,3,4. is it possible to sync the time of switches and routers with this server. Need suggestion on this.Rgds,Sarbudeen
Hello ,My name is Sunil C.i have a Cisco CSM Load Balancer.I can use it to Load Balance two physiscal web servers with Apache and Tomcat.Now consider this scenario.i have only one web server (for testing purpose).It contains Apache and Tomcat.I have ...
1. How should I connect my NEW proposed data centre in India (Delhi) with the central data centre in Germany ?2. what sort of International Link I should go for ?3. who are the solution provider in India can provide such International connectivity...
Hi all,I need to write testcases to test IP Fragmentation and IP option.Like,1.when fragmenting the IP packet, IP option should be copied correctly to all the fragments.2.Different frame size, etc.Kindly let me know some testcases to test this featur...
What is the logic behind setting rip hop count to only 15 ?This question may sound stupid, but i have curiosity to know this...Thanx
Dear expertsWe work in a Company with over 800 Cisco devicesUsing ATM with varios speeds ( from 4 Mb/s to 52 Mb/s ) On the Backbone ( redundated ) links We usually find a lot of CRC ( aalsnap5 enc. ) degradation.Anyone has got a idea to shut the pir...
Is it possible to put a second WAN interface card into a 2800 series router to connect two different ISP's to the same router. I need to load balance and use static routes, so I was hoping to plug two different ISP services into one router. I had bee...
I have a 6509 with a mfsc blade which is configured for routing (it is one of my routers). Can I use SDM for this product?thank you
Hi there,we must change the NPE300 of our 7024VXR,cause of hardware failure. Since this, we have Output Drops on the POS Modul low Bandwidth, means on our POS Line (155MBit/s) we could only transfer aprox. 130MBit/s.Hardwaredetails:7204VXT with NPE30...
I have a facility that has WAN connectivity problems. I have an AT&T Frame-relay MPLS WAN. If I have the circuit connected to the router via a WIC-1DSU-T1-V2 the circuit will not come up. If I connect the same circuit to the same router via a VIC-...
Hello folks,I have a little problem that requires our attention. I am having some problems with a link. On one end of my router, I see the serial interface up, line protocol up yet I cannot even ping that interface. The other end is in up/down state....
HelloIf we have 3pcs of 2006 WLC and 17 pcs og 1010 APhow many clients can maximum connect to the wireless network, and how many can operate at one 1010APTanks//...Best RegardsLars Thobiasen
Hi, I have a Cisco 837 running fine in VPN mode (see attached config) and today I upgraded it to an 877 (se attached config) but I quickly took it off.The VPN (on the 877) establishes and all the users can ping the servers at the other side of the VP...
I have a 2611XM and a 2621XM router. Can these support T3? I see there is a NM-1T3/D3, but it does not specify these routers as supported models.Is this correct and do these platforms not support T3?Regards,Christopher
From my Cisco 877 and 1841 with ADSL consoles, how can I test that a UDP port is able to reach a remote server over the VPN?Is there a commadni can run?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-22-2025 10:50 PM | ||
05-19-2025 12:25 PM | ||
05-15-2025 07:28 AM | ||
05-13-2025 03:49 AM | ||
05-12-2025 03:28 PM |
User | Count |
---|---|
4 | |
3 | |
2 | |
2 | |
2 |