ASA 5510 10/100 interface doesnt get the IP address from DHCP server untill unless you hit the renew DHCP button. Has anyone ever come across a problem like this?
ASA 5510 10/100 interface doesnt get the IP address from DHCP server untill unless you hit the renew DHCP button. Has anyone ever come across a problem like this?
HiHow do i configure my router to act as a NTP server so that all my xp workstation are able to get the time from this ntp server. And also this ntp server will get the time from the external source. I have a cisco 1720 router with ADSL connection to...
Hi All,My 3821 DMVPN hub router has this configuration and the MTU may be higher than it should be.interface Tunnel0 description Tunnel for DMVPN bandwidth 4500 ip address 10.x.x.x 255.255.255.224 no ip redirects ip mtu 1416 no ip next-hop-self eigrp...
Can I log NATing events e.g. what private IP was translated into real IP for any destination and port. In fact we are running both NAT and PAT on our 7600 router.
I have been trying to plug in the different metrics (bandwidth, delay, reliability, load, and mtu) into the EIGRP metric formula, but have been unsuccessful at figuring out how it comes up with the composite metric. Here is the info I havedefault me...
Hi All,I have had never been able to understand on whose recommendation (I mean if we need to check with the carrier or not) we need to buy PAs for a 7200VXR for DS-3I have come across ATM PA-A3 and the PoS PA both could be used to connect the DS-3, ...
I have two routers R1 --- R2, both running OSPF, both in full adjacency.If I configure BGP in both routers, and configure redistribute static in R1, then R2 should see those static routers, correct? Why am I not seeing those routes?R1 config:router b...
Hi All,I have 2 Mpls links from two service providers terminating on same router how can i load balance them efficiently.regardsMukesh Dahiya
Hi,I have 3 routers that each have one interface on the same VLAN, Rtr1 is DR, Rtr2 is BDR, and Rtr3 is DRother...Doing 'sh ip route' on RtR3 shows 2 paths to network X.X.X.X behind Rtr1 and Rtr2 via Rtr1 and Rtr2. The problem is that packets from Rt...
Dear All;I have a secnario;I have two ERP server for same purpose. 1 of two is standby server. now i wana configure that server in such a way that if primary server goes down, standby server should be up as a primary one. in other way, i wana configu...
I'm rather new to BGP and am looking at redesigning a section of our global WAN, but have found myself stuck. North America WAN is routing bgp over mpls. We have two locations in South America, one connected to the North America WAN, the other conn...
How do you update the firmware on a Sup720 (WS-SUP720)? Is that possible or not? recommended? I have tried to look for documentation on cisco's website but have had no luck. Thank you.
Hi,I have two cisco routers,on both the routers a 2Mbps internet link is terminated from different service provider.How to configure and provide load sharing accross 2 links and failover if one of the link is down.
How to disable AAA on 3750 switch which has got screwed up. I believe RMON mode will not work?
Hi Everyone,Can any one explain me the troubleshooting techniques of voice problem like echo,jitter or any weblink that can guide me.Many Thanks Manish Prasad
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
06-14-2025 01:24 AM | ||
05-12-2025 03:28 PM | ||
05-09-2025 02:25 PM | ||
05-05-2025 11:47 PM | ||
04-22-2025 12:20 PM |
User | Count |
---|---|
9 | |
7 | |
4 | |
4 | |
3 |