Can someone please tell me how to FTP an image to a 2811's flash?Thanks,Chris
Can someone please tell me how to FTP an image to a 2811's flash?Thanks,Chris
I have been tasked with redesigning a network for between 50-100 people. The network is currently a single subnet (no vlan. I have the following equipment to work with and I am soliciting advice about its implementation.I have a 2811 Router, 3650 c...
anyone knows of links about building up a callcenter from scratch? whitepapers, documentations, tutorials, whatever...thanks
My 1811 switchport link lights only display if the FE0 light is off. They both do not stay on at the same time. It's an either or situation. The switchport doesn't seem to want to be active when the FE0 is active. I can powercycle the router and eith...
Hi there,Does anyone know if an FRF.16.1 P router (Label Switch Router) trunk can be configured to carry MPLS labels used in the forwarding plane? I've searched high and low on the web for information, including the MPLS/Frame Relay Forum, and have f...
Hi Guys, Hopefully someone will be able to answer something that is driving me nuts. I'm mainly a LAN guy and the closest I've got to ISDN was quite a few years ago as a back up to a serial line. My question is why must you have a NM4 B S/T or the 8 ...
I have a 7206 Frame-Relay router with two HSSI interfaces. My question is, is it possible to have the same DLCI (100) on both interfaces?
Hi all. I've c2801 and after powering on router no boot automatically, each time i've to run it by command: boot.Below is the bootup message that appears: System Bootstrap, Version 12.3(8r)T8, RELEASE SOFTWARE (fc1)Technical Support: http://www.cisc...
Since I'm very fresh in the cisco world I figured it would be beneficial for me to ask this question here. If I have a 20MB line and want to fully utilize that 20MB line between 2 remote sites which router should I purchase. The remote sites also run...
i have pix 525 firewall and 4215 IDS, i am new to this field & i want implement the security policies for our network inorder to protect the network.so send me the details about which port i have to block and which i have to permit and other importan...
my 2600 series router can't detect it's interfaces both serial and fastethernet.when i enter the command interface fa0/0 or fa0/1 or interface s0/0, in global config mode. it returns an invalid command output. i installed a new serial port module so ...
Could anyone help me out, which CISCO router model does support min. 100kpps performance for internet purpose? What about 2811 w/64F/256D, does it support...AK
Hi,This situation is very surprising !On our 2 mbps point to point link we get perfect ping from one router to another router serial address also a perfect ping from Pc's from either side of link. With no input error's and no CRCS. But when we sta...
Hello friends,I'm confused about the WAN links in general especially the interfaces, channelized, unchannelized.For example i have a E1 connection "2 M" from my telecom and i have Cisco 2821 router with WIC-1T, now i have the following questions:- In...
Hi, our company currently connect a C2811 to MPLS through ADSL.there is another cisco 837 adsl router, which isnt connect to the Mpls.we would like to have another adsl service on the 2811 router with a static public ip, so that we may able to settle...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-22-2025 10:50 PM | ||
05-22-2025 09:48 PM | ||
05-19-2025 12:25 PM | ||
05-15-2025 07:28 AM | ||
05-13-2025 03:49 AM |
User | Count |
---|---|
4 | |
3 | |
2 | |
2 | |
2 |