Routing

I am hoping someone can help me with the following configuration. This may be an elementary configuration but I am just really getting started working with Cisco routing so any help would be much appreciated. I have I have a Cisco 1841 router with 2...

i have 2 class c remote network w/c am connected directly through a point-to-point. can i sum the network in single command??e.g. 10.10.1.0 & 10.10.2.0 to be routed to my serial or remote next hopip route 10.10.10.1 255.255.254.0 serial1/0 or( A.B.C...

Good Morning! I had cisco 7206 router with ssh server enabled on it. After clearing nvram and deploying the same config file(copy and paste), i can't enable ssh! .there is no "crypto key generate" command.Has anybody had the same problem?

hi,can anyone give an explanation on thedifferences between wire speed and line rate.thanks,thomas.

I face an issue with a 7206vxr having both NPEG1 and an I/O FE controller. The boot sequence of the IOS image first line points to image on the NPEG1 and second to the one on the I/O controller. Still the router boots with the second image from the I...

The stub area types can be summarized as follows:Stub Type--------------LSAs-------------Default InjectedStub-------------------1,2,3,4---- ---------------YESTotally Stubby---------1,2,default of 3-----------YESNSSA-------------------1,2,3,4,7-------...

Dear sir,i have configured cisco 2811 router in central site which have six wan interface. in central side i have three network.1. 192.166.2.0/242. 192.168.1.0 /243. 192.168.10.0/24my router fastethernet ip is 192.166.2.202 and i want to access my se...

Dear All,I would like to know which routers that can be use as PPPOE NAS also is that 1600&1700 can support it and which IOS version can be use.

Hi all,I am interested in any answer or document that dicusses how a Cisco 3660 can take in a 1500 byte packet on its Ethernet interface and put it on to (i) 2xE1 lines.(ii) FR network (1Mbps)1. What is the time taken to break up the packet for plac...

I am facing a problem, I have a 3745 VPN K9 Bundle. When installing NM-2W and WIC-2T in it and when the AIM module activated, I get the attached error messages and the serial interface goes down.

we have four routers in square A B C D A D in the top and B C in the bottomB C has 10 Mbps link between B to A and C to d there is 2*2Mbps link.The problem is whenever one of the 2Mbps link goes down outgoing packet which are supposed to travel lets...

hii have a main router in the center and a lot of branch . all the branch connect to the main router with adsl (dialer 0 )and nat too.in all branch router i have interface loopback.the problem is that i want to arrive from the main router to all the ...

Hello,I have one existing Internet connection to ISP1. Because of the ISP1 is not stable, so I decided to connect other ISP as ISP2 for Backup. The problem now is that my Firewall Box1 is using Public ip address of ISP1, but when the ISP1 is getting ...

Requirement : Part of the acquisition agreement between AS 300 and AS 200 includes stipulations on what traffic AS 300 will provide transit for. This agreement states that AS 300 will not provide transit for traffic coming from AS 60 and its customer...

hiI've done a Release upgrade from 12.1(12c)EA1 to 12.1.22-EA6 on the Catalyst WS-C3550-12T now I cannot start a web interface and get following error:404 Not FoundThe requested URL /homepage.htm was not found on this server.