Hello, I'm new in networking and I'm working on this network assignment for uni and i've been stuck for a few hours now. I'm not able to ping the router from the multilayer switch or the otherway around.This is a screenshot of my work so far This is...
Good Day Team, I would like to design and implement a campus network but I'm in a bit of confusion on how and where to begin this from scratch. My knowledge is limited to CCNA but I'm curious to know how this is implemented in real life(production).A...
Hi all, I was just checking a dhcp ip helper address concept. I have a router as dhcp server from another network (through WAN), it give s dhcp thorugh an ip heper address configuration on LAN succesfully. However problem is I cannot ping default gat...
Dear all, I am kind of new in the firewall management and got my first issue which I can't solve no matter what I try. I have a Cisco ASA 5505 with ASA 8.4(3) where I try to open the port 9101 for a local server over the internet. I ran Packet Trac...
Hello,My question is about the ability of the ASR1001 to be able to manage the full-routes (V4/V6) learned by R1 and R3...R2 = ASR1001 RP1 with 8Gb DRAM Will the use of ASR1001 in iBGP sessions with R1 and R3 be possible ?neighbor ibgp-pgroup peer-gr...
Hello, I'm configuring my network, but I don't know how to setup the routing. I do have a Cisco SG350. On both the R1 (PfSense) and R2 (SG350) I setup VLANs. The VLANs at R1 and R2 are in the same subnet. I only changed the IPs for the gateway, as yo...
Hi all, I have two offices A and B. Office A has Sophos Firewall and Office B has a Cisco VPN router. We have already created a tunnel between Office A and Office B (Sophos to Cisco). Now the problem is when I connect to Office A (where my Sophos FW ...
Hi! I have cisco ISR-4431 router i want to know how many concurrent sessions of VPN like IPsec or GRE can be handled by my router?
UPDATE: Sent the router back. I had no knowledge of Command-based setup and neither does our local networking businesses. Even if I could get it working, I'd be at a loss for any issues that occur. Going to attempt sticking with the RV340. I will sta...
Hi the Community,I still have the same problem and would need your help. As you can see on the attached chart. I would like to force the route choice from the blue network to the green network to use "Site main router". Sometime on my production netw...
I thought this would work to prepend only the default route 0.0.0.0/0 but it ended up prepending everything. On an IOS XR platform conf t!prefix-set PREPEND_CUST0.0.0.0/0end-set!route-policy CUST_PREPEND_ASif destination in PREPEND_CUST thenprepend ...
Hi everyone We are advertising the 172.30.240.0/20 subnet to a neighbor 1. We need to advertise 172.30.240.0/24 to another neighbor 2. This is the configuration we have, but it is not working Neighbor 1 (It´s working) interface TenGigabitEthernet0/1/...
Hi, Does ASR9000 and NCS5500 support IPv4 over MPLS without VPN?I'm in trouble because I can't find a clear statement in Cisco's web site.I tried with the following Config, but MPLS label was not attached and communication was performed with Pure IP....
Hi all, I'm currently using a C887VAG-4G-GA-K9 with the cellular as backup. To activate the cellular as back-up I use a script. This usually works just fine, but the router recently started flapping..This activated the script over and over again.This...
Hi,I have attached PT-Topology for VLAN configuration.Used vlan10,20,30 in SW1 & SW2.End devices connected to SW1 & SW2 is assigned with ip addresses in same subnets in both switches in respect with vlans.I've created sub interfaces(Fa 0/0.10,0.20&0....
