Hi, Does ASR9000 and NCS5500 support IPv4 over MPLS without VPN?I'm in trouble because I can't find a clear statement in Cisco's web site.I tried with the following Config, but MPLS label was not attached and communication was performed with Pure IP....
Forum Posts
Hi all, I'm currently using a C887VAG-4G-GA-K9 with the cellular as backup. To activate the cellular as back-up I use a script. This usually works just fine, but the router recently started flapping..This activated the script over and over again.This...
Hi,I have attached PT-Topology for VLAN configuration.Used vlan10,20,30 in SW1 & SW2.End devices connected to SW1 & SW2 is assigned with ip addresses in same subnets in both switches in respect with vlans.I've created sub interfaces(Fa 0/0.10,0.20&0....
Hi,I would like to know with cisco DMVPN solution,"only HUB site need to have Public IP address and the other spoke sites do not need to have public IP address"Is it correct? As long as the spoke sites get access to the internet, DMVPN will be work ?...
Resolved! BGP Dampening Max suppress time
Hi, What happens after max suppress time in BGP dampening? For example: Penalty value = 100 Re-use = 50 Suppress = 125 half-time= 15 mins The penalty of the route has reached 600 and the route is in a suppressed state. If the timer hits 60 mins, I un...
Need help in Routing protocol !!We have 2 link one is internet and other is Mpls link terminated in 2 different firewall.We already running an voice setup in internet link and now data setup in MPLS link perfectly.The setup is like Voice vlan and dat...
Hello All, We are configuring OSPF with 03 VRF , on Same Interface (Cisco Router) divided into sub-interfaces. We are running 03 different OSPF process per VRF. We have configured only 1 Loopback in our router to use as router-id for all the OSPF...
HII am using a bunch of ASR1002-X for PPPoE termination.All of them except one I am using IOS 16.6.7 and provide services to up to 20K subscriber. On one ASR I installed 16.12.14 IOS, When I try to terminate PPPoE session I get this log: Aug 19 08:49...
Hi, this is a simple issue but I have been looking at documentation and I can't get anywhere so I will ask the experts...I am setting up a DHCP server on an 1841 router with a HWIC-AP-AG card. It's running IOS 15.1(3)T2 adventerprise with 256 Mb of r...
Hello EveryoneI am building a home lab to practice on real equipment for Exams. I have gone through some sites trying to find a solution to my problem, but I am falling short.Any help would be greatly appreciated. Router show runBuilding configurati...
Resolved! Troubleshooting ACL SSH
Hello!I don't understand this common error with configuring ACLSo R2 have extended access list configured on interface e0/0 (inbound) R2# show access-lists 150 Extended IP access list 150 10 deny tcp any host 13.1.1.1 eq 22 20 permit ip any anyBut...
I want a select group of BGP routes to have inferior EIGRP metrics upon redistribution. Will this route map and set metric command work? Or will the metric from redistribute command override the settings? router eigrp 1redistribute bgp 65012 metric...
Hi, this is a simple issue but I have been looking at documentation and I can't get anywhere so I will ask the experts...I am setting up a DHCP server on an 1841 router with a HWIC-AP-AG card. It's running IOS 15.1(3)T2 adventerprise with 256 Mb of ...
Router#sh ip protocols Routing Protocol is "ospf 1"Outgoing update filter list for all interfaces is not setIncoming update filter list for all interfaces is not setRouter ID 4.4.4.4Number of areas in this router is 2. 2 normal 0 stub 0 nssaMaximum p...
Resolved! BGP not to advertise a prefix
Hey!I need to tell my eBGP-neighbor not to advertise a prefix to its specific neighbor. I know that BGP community no export tells BGP neighbors to advertise a prefix only to iBGP neighbors.Thus with no-export I can tell my neighbor not to send a pref...
