I want to distribute only one static route to OSPF.ip route 10.55.254.0 255.255.255.192 10.80.60.5 My config:ip prefix-list DMZ201 seq 10 permit 10.55.254.0/26route-map DMZ201-TO-OSPF permit 10 match ip address prefix DMZ201 router ospf 200redistribu...
Forum Posts
Resolved! Help with Simple Routing on ASR920
I would like to achive a very simple configuration, but for some reason it's not working for me on the asr920.Here is the layout I have. And this is the configuration on the ASR:interface GigabitEthernet0/0/0 description To_ISP ip address 165.228.13...
Am I missing something? We have 5 statics, and have Comcast Business gateway. I have a Linksys Wi-Fi router connected to the router, and it is reaching the internet with the same numbers inserted in this configuration. However, I am unable to ping 8....
Resolved! OSPF Network Command Confusion
Hi there,I am having a problem to understand the exact role of the network command under the OSPF process, I am talking about OSPF V.2 here. I understand that network statement is NOT used to advertise networks but it is used to enable OSPF on an int...
Resolved! QoS for Voice Example
Hello, I need a simple QoS that will reserve bandwidth for VOIP over L2VPN link.One member posted this:class-map match-all voicematch ip rtp 16384 16383-----> matches RTP audio orMatch access group name voice ip access-list extended voicepermit udp 1...
Hi, As title says, I have a new ASR901 fresh from the box. I'm unable to no shut port 10 or 11 which I believe are flex ports. I recieve an error "license-request_failed:"I believe I understand that I need to activate a license of some sort but after...
So if you have a multi-layer switch which is connected via layer 2 switchport to another switch heading to main campus and/or out to core network devices, can you install another device let's say router or FW on a port configured for Layer 3 and traf...
I'm trying to open a port to a server using Port Forwarding. When I setup port forwarding to go to a server on the default VLAN, everything works fine, external requests to that port are forwarded to the server and the server responds.However, if I ...
I have a situation where my Internet edge routers learn 0.0 from ATT (AS 7018) my provider. I then wish to advertise these learned routes via WAN. However my WAN MPLS provider is also ATT and they use AS 7018 for that as well. When I try to push 0...
Resolved! Stopbit Command Question
So I am running through some configs that one of our previous engineers used in a router config and came across the stopbit 1 command on line con 0. Can someone explain what the stopbit is and why you would use this command at all? I have just neve...
At least with srr-queue i can sort of do something to manage speeds.. but with upload.. acl.. access group.. policy .. police... jesus.. i can not find one guide that actually works from beginning to end.. im desparate to be able to do this.. im tryi...
Resolved! Cisco ISR Throughput
Hi guys, i'm new to networking and just want to upgrade the old router on my branch. As i read ISR 4321 documentation it states that 50Mbps-100Mbps system throughput. Does it means that if i have 1Gbps internet capability from ISP, with default lice...
Hi, I installed CSR1000v router on my hyper-v with demo license AX 2,5gbps and I tried some throughput test. During testing (around 600MB/s should be 900+) I discovered that one core is fully loaded when others are not. VM router have assigned 4 vcpu...
I have 2 2951 routers, running the same IOS (c2951-universalk9-mz.SPA.156-3.M2.bin). I am setting this up with the Cube license, and while waiting I activated the eval rtu advuck9 license, then ordered what I was told all I needed was the uck9 paper...
How would you use OSPF or EIGRP to get a VRF-Lite SVI network into the routing process? I have seen routing redistribution and a route to a firewall but was wondering if anyone else uses a different way? Or what is the best way? Really stuck on how w...
